Feeds
質問
Rate Transition block outputs zero on the geenrated code interface despite the input , though it works fine during simulation.
I am using a Rate Transition block, as shown in the picture below, in my Simulink model. The input to this block represents a re...
12ヶ月 前 | 0 件の回答 | 0
0
回答回答済み
I am having problems with the install_addon.m
When I downloaded the function, it has the name 'installaddon', not 'install_addon'. Make sure of the function name, and if it i...
I am having problems with the install_addon.m
When I downloaded the function, it has the name 'installaddon', not 'install_addon'. Make sure of the function name, and if it i...
1年以上 前 | 0
質問
Two different models for the stepper motor in Simscape stepper motor blocks
I found in Simscape two differnt blocks for the stpper motor SM block 1 SM block 2 Before going to the question, In t...
1年以上 前 | 1 件の回答 | 0
1
回答質問
Problem in Stepper Motor block Parameters with predefined parametrization
I am using the stepper motor block provided in the Simscape toolbox R2020b. I used the predefined parametrization from the provi...
2年弱 前 | 1 件の回答 | 0
1
回答質問
Modeling of hybrid stepper motor (HSM) using Simulink
Hi all, I am trying to build a Simulink model for HSM, using the math model in photo p1. This model is the same seen in Matlab ...
2年以上 前 | 0 件の回答 | 0
0
回答質問
How to Extract X,Y,Z vectors from grid data?
I have the below data from contour grid, but I am not sure how to deal with it, the data are more than 3000 rows. I have two que...
3年弱 前 | 1 件の回答 | 0
1
回答質問
Stateflow shows a dimension error for an output port?
I am using Statefloe, specifically, Simulink based state and experiencing a problem. My Model have 5 states and uses one simulin...
約4年 前 | 0 件の回答 | 0
0
回答質問
How to find intersection of several data sets?
I have 50 sets of (x, y) points, and each set contains handreds of points, I am trying to find the intersection points between t...
4年以上 前 | 1 件の回答 | 0
1
回答回答済み
I wanted the matlab to show 5 places after the comma.
Hello lucass! Try, vpa c=1/3 vpa(c,5)
I wanted the matlab to show 5 places after the comma.
Hello lucass! Try, vpa c=1/3 vpa(c,5)
4年以上 前 | 0
| 採用済み
回答済み
How to solve a system of equations mixing non-linear ODE and non-linear "simple" equations?
The solvers usually able to solve index-1 DAE, not all the equations are apperent but you have too many variables you mostly nee...
How to solve a system of equations mixing non-linear ODE and non-linear "simple" equations?
The solvers usually able to solve index-1 DAE, not all the equations are apperent but you have too many variables you mostly nee...
4年以上 前 | 0
回答済み
Multiple variable inputs for a function
The logical order of the code is not correct and the function definition as well. A guide code can help you to reconstruct your...
Multiple variable inputs for a function
The logical order of the code is not correct and the function definition as well. A guide code can help you to reconstruct your...
4年以上 前 | 0
質問
Interface Simulink based clutch device with Simscape driveline loop
Hello Everyone! I am trying to simulated the gear change behavior in a vehicle transmission using Simulink and Simscape drive...
4年以上 前 | 1 件の回答 | 0
1
回答質問
Spatial contact force block
Hi I am trying to build a model for the dog clutch with Simscape multibody as shown in the below figure. each side can rotate ...
5年弱 前 | 1 件の回答 | 0
1
回答質問
How to convert 3d scattered points to coloured map?
I have three column vectors xp, yp, zp, where each column set of these vectors form the coordinate for a point in 3d space. I us...
約5年 前 | 1 件の回答 | 0
1
回答質問
How to fix cropped legend of non-default sized plot figure?
Hi MATLAB Users! I have to prepare some plot using MATLAB to a predetermined size. I made a figure with the default size then r...
約6年 前 | 1 件の回答 | 0
