このページは前リリースの情報です。該当の英語のページはこのリリースで削除されています。

モデル化

STM32 プロセッサベースのボードを使用したハードウェア接続用のモデルの準備、ハードウェアプロトコルをサポートするためのブロックの追加

ブロック

STM32F4xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
CAN Read	Read message from CAN network (R2023a 以降)
CAN Write	Write data to the CAN Bus (R2023a 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
I2S Audio Out	Send processed audio samples to audio devices (R2023a 以降)
I2S Mic In	Read audio sample from MEMS microphone available on the STM32F4xx based board (R2023a 以降)
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
SPI Receive	Receive data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Transmit	Transmit data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Controller Transfer	Write data to and read data from SPI peripheral device (R2023a 以降)
TCP Receive	Receive data over TCP/IP network from remote host (R2022b 以降)
TCP Send	Send data over TCP/IP network to remote host (R2022b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UDP Receive	Receive UDP packets from UDP host (R2022b 以降)
UDP Send	Send UDP packets to UDP host (R2022b 以降)

STM32F7xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
CAN Read	Read message from CAN network (R2023a 以降)
CAN Write	Write data to the CAN Bus (R2023a 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
I2S Audio Out	Send processed audio samples to audio devices (R2023a 以降)
I2S Mic In	Read audio sample from MEMS microphone available on the STM32F4xx based board (R2023a 以降)
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
SPI Receive	Receive data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Transmit	Transmit data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Controller Transfer	Write data to and read data from SPI peripheral device (R2023a 以降)
TCP Receive	Receive data over TCP/IP network from remote host (R2022b 以降)
TCP Send	Send data over TCP/IP network to remote host (R2022b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UDP Receive	Receive UDP packets from UDP host (R2022b 以降)
UDP Send	Send UDP packets to UDP host (R2022b 以降)

STM32G4xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
Comparator	Compare two analog inputs on peripheral and provide results (R2023b 以降)
CORDIC	Enable hardware acceleration of trigonometric and hyperbolic mathematical functions (R2023b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
FDCAN Read	Read data from CAN FD Bus (R2023a 以降)
FDCAN Write	Write data to the FDCAN Bus (R2023a 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
Higher Resolution Timer	Generate high resolution pulse width modulated waveforms (R2022b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
I2S Audio Out	Send processed audio samples to audio devices (R2023a 以降)
I2S Mic In	Read audio sample from MEMS microphone available on the STM32F4xx based board (R2023a 以降)
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
SPI Receive	Receive data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Transmit	Transmit data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Controller Transfer	Write data to and read data from SPI peripheral device (R2023a 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)

STM32H7xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
Comparator	Compare two analog inputs on peripheral and provide results (R2023b 以降)
CORDIC	Enable hardware acceleration of trigonometric and hyperbolic mathematical functions (R2023b 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
FDCAN Read	Read data from CAN FD Bus (R2023a 以降)
FDCAN Write	Write data to the FDCAN Bus (R2023a 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
Higher Resolution Timer	Generate high resolution pulse width modulated waveforms (R2022b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
SPI Receive	Receive data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Transmit	Transmit data through Serial Peripheral Interface (SPI) on target (R2023a 以降)
SPI Controller Transfer	Write data to and read data from SPI peripheral device (R2023a 以降)
TCP Receive	Receive data over TCP/IP network from remote host (R2022b 以降)
TCP Send	Send data over TCP/IP network to remote host (R2022b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UDP Receive	Receive UDP packets from UDP host (R2022b 以降)
UDP Send	Send UDP packets to UDP host (R2022b 以降)

STM32L4xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
CAN Read	Read message from CAN network (R2023a 以降)
CAN Write	Write data to the CAN Bus (R2023a 以降)
Comparator	Compare two analog inputs on peripheral and provide results (R2023b 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)

STM32L5xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
Comparator	Compare two analog inputs on peripheral and provide results (R2023b 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Digital to Analog Converter	Configures the DAC to generate an analog voltage on the specified DAC channel (R2023a 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
FDCAN Read	Read data from CAN FD Bus (R2023a 以降)
FDCAN Write	Write data to the FDCAN Bus (R2023a 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)

STM32WBxx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)

STM32U5xx ベースのボード

Analog to Digital Converter	Convert analog signal on ADC input pin to digital signal (R2021b 以降)
Digital Port Read	Read GPIO pin status (R2021b 以降)
Digital Port Write	Set GPIO pin status (R2021b 以降)
Encoder	Measure rotation of encoder in counts (R2022b 以降)
FDCAN Read	Read data from CAN FD Bus (R2023a 以降)
FDCAN Write	Write data to the FDCAN Bus (R2023a 以降)
Hardware Interrupt	Trigger downstream function-call subsystems from interrupt service routine (R2021b 以降)
I2C Controller Read	Read data from I2C peripheral device or I2C peripheral device register
I2C Controller Write	Write data to I2C peripheral device or I2C peripheral device register
PWM Output	Generate square waveform on enabled channels using timer module (R2021b 以降)
Timer	Starts timer counter and provides current counter value (R2022b 以降)
Timer Capture	Output the capture compare register value (R2022b 以降)
UART/USART Read	Read data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)
UART/USART Write	Write serial data from the Universal Asynchronous Receiver Transmitter (UART/USART) port (R2022a 以降)

ユーティリティブロック

Byte Pack	入力信号を `uint8` ベクトルに変換
Byte Unpack	`uint8` ベクトルを入力信号に変換
Byte Reversal	入力語のバイト順を反転
Memory Copy	Copy data from and to memory section
Protocol Encoder	Encode input data into a uint8 byte stream by specifying the packet structure (R2023a 以降)
Protocol Decoder	Decode a uint8 byte stream by specifying the packet structure (R2023a 以降)

モデル設定

Model Configuration Parameters for STM32 Processor Based Boards

トピック

Configure STM32 Processor-Based Boards using STM32CubeMX with Simulink
Configure the STM32 Processors-Based Boards to use STM32CubeMX project with Simulink.
Configure Ethernet Options in STM32CubeMX for STM32 Processor Based Boards
Ethernet configuration in STM32CubeMX project.
Set Up Scheduling Options for STM32 Processor-Based Boards
Setting up scheduling options for STM32 processor based boards.
Use SoC Blockset Pass-Through Block Simulation
Use the SoC Blockset™ block pass through to add simulation to STM blocks.

注目の例

Getting Started with STMicroelectronics STM32 Processor Based Boards

Use the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors to run a Simulink® model on an STMicroelectronics STM32 Processor Based hardware board.

モデルを開く

Using Hardware Interrupt Block to Create an ISR on STMicroelectronics STM32 Processor Based Boards

Use a Hardware Interrupt block to create an interrupt service routine (ISR) in the generated code for Embedded Coder® Support Package for STMicroelectronics® STM32 Processors Based Boards.

モデルを開く

Using the Analog to Digital Converter Block to Support STMicroelectronics STM32 Processor Based Boards

Use Analog to Digital Converter block in a Simulink® model to digitize analog signals connected to analog input channels using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.

モデルを開く

Signal Monitoring and Parameter Tuning of Generated PWM Output

Use PWM Output block in a Simulink® model to generate PWM signals using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.

モデルを開く

Voltage Mode Control of DC-DC Buck Converter and Boost Converter Using STMicroelectronics STM32 Processor

Implement a DC-DC buck converter or Boost Converter control system using the B-G474E-DPOW1 Discovery kit for Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.

モデルを開く

Open-Loop Control of 3-Phase AC Motors Using STM32 Processor Based Boards

Uses open-loop control (also known as scalar control or Volts/Hz control) to run a motor. This technique varies the stator voltage and frequency to control the rotor speed without using any feedback from the motor. You can use this technique to check the integrity of the hardware connections. A constant speed application of open-loop control uses a fixed-frequency motor power supply. An adjustable speed application of open-loop control needs a variable-frequency power supply to control the rotor speed. To ensure a constant stator magnetic flux, keep the supply voltage amplitude proportional to its frequency.

モデルを開く

Sensorless Field-Oriented Control of PMSM Using STM32 Processor Based Boards

Implements the field-oriented control (FOC) technique to control the speed of a three-phase permanent magnet synchronous motor (PMSM) based boards. For details about FOC, see Field-Oriented Control (FOC) (Motor Control Blockset).

モデルを開く

Estimate PMSM Parameters Using STM32 Processor

Determines the parameters of a permanent magnet synchronous motor (PMSM) using the recommended STM32xx based board. The tool determines these parameters:

モデルを開く

Exchanging Ethernet Data with STM32xx Based Boards

Send and receive UDP and TCP messages on STM32xx processor based boards using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.

モデルを開く

Parametric Audio Equalizer for STM32 Discovery Boards

Model a three band parametric equalizer algorithm and run it on the ARM® Cortex®-M based STMicroelectronics® STM32 Discovery boards using Embedded Coder® Support Package for STMicroelectronics STM32 Processors.

モデルを開く

G.729 Voice Activity Detection for STM32 Processor Based Board

Model the ITU-T G.729 Voice Activity Detector (VAD) algorithm and run it on the ARM® Cortex®-M based STMicroelectronics® STM32 boards using Embedded Coder® Support Package for STMicroelectronics STM32 Processors.

モデルを開く

Using SPI to Read and Write Data to SPI EEPROM on STM32 Processor

Configure and use SPI blocks to read and write data using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors.

スクリプトを開く

Communication Using CAN or FDCAN Blocks for STMicroelectronics STM32 Processor Based Boards

Use CAN or FDCAN blocks to communicate with the STM32 processor based boards using Embedded Coder® Support Package for STMicroelectronics® STM32 Processors Based Boards.

モデルを開く

モデル化

ブロック

STM32F4xx ベースのボード

STM32F7xx ベースのボード

STM32G4xx ベースのボード

STM32H7xx ベースのボード

STM32L4xx ベースのボード

STM32L5xx ベースのボード

STM32WBxx ベースのボード

STM32U5xx ベースのボード

ユーティリティ ブロック

モデル設定

トピック

注目の例

Getting Started with STMicroelectronics STM32 Processor Based Boards

Using Hardware Interrupt Block to Create an ISR on STMicroelectronics STM32 Processor Based Boards

Using the Analog to Digital Converter Block to Support STMicroelectronics STM32 Processor Based Boards

Signal Monitoring and Parameter Tuning of Generated PWM Output

Voltage Mode Control of DC-DC Buck Converter and Boost Converter Using STMicroelectronics STM32 Processor

Open-Loop Control of 3-Phase AC Motors Using STM32 Processor Based Boards

Sensorless Field-Oriented Control of PMSM Using STM32 Processor Based Boards

Estimate PMSM Parameters Using STM32 Processor

Exchanging Ethernet Data with STM32xx Based Boards

Parametric Audio Equalizer for STM32 Discovery Boards

G.729 Voice Activity Detection for STM32 Processor Based Board

Using SPI to Read and Write Data to SPI EEPROM on STM32 Processor

Communication Using CAN or FDCAN Blocks for STMicroelectronics STM32 Processor Based Boards

ユーティリティブロック