Yifeng Tang

MathWorks

Last seen: Today | 2020 年からアクティブ

Followers: 10 Following: 0

Programming Languages:
Python, MATLAB, Fortran
Spoken Languages:
English, Chinese
Pronouns:
He/him
Professional Interests:
Physical Modeling, Simscape Fluids, Simscape, Heat and Mass Transfer, Thermodynamics and Heat Transfer

統計

All

バッジを表示

Feeds

回答済み
Modelling multistage expansion of compressed air in a single cylinder engine
Hi @Kyle I feel like the model should look similar to that diagram you have. Single-cylinder engines can be modeled using a Me...

1日前 | 0

回答済み
Linking Mechanical and Hydraulic System Model in SIMSCAP MATLAB
The Translational Multibody Interface was first available in R2021a. Prior to that, such interface can be doen using force sens...

2日前 | 0

回答済み
Adding input for valid parameter in Simscape block
Hi @Florian, I think it's possible. The Simscape code of this block is visible. You may find it in the Description tab of the...

2日前 | 0

| 採用済み

回答済み
Modelling a Dehumidifier with Simscape Fluids System Level Heat Exchanger(TL-MA) not possible?
The error is complaining that the parameters you've set don't make sense :p For example, you've set the operation condition to ...

2日前 | 0

回答済み
On how to use the Two-Way Connection Block
Hi @CAME, I've seen this in earlier version of Powertrain Blockset examples. I took some snapshot from this "Conventional Vehi...

8日前 | 0

回答済み
Model leaks in tanks and valves in a gas SIMULINK system
(Moved to Answer from Comments) It sounds like you have some values as a "standard" leak rate, is that right? I would assume y...

12日前 | 0

回答済み
Bonjour, je souhaite modéliser un piston et j'ai une erreur. Merci
In your model, the B & F ports of the prismatic joint is connected to the B & F port of a rigid transform block. This will fix ...

14日前 | 0

回答済み
PEM fuel cell heat management
Looks like it should be instead. Would you agree? I checked the source code and the power dissipation term is calculated as ...

15日前 | 1

回答済み
Trace Gas Removal Loop
Hi Ryan, The logic you have in mind is likely to trigger lots of zero-crossing/chattering, and as @Walter Roberson pointed out,...

19日前 | 1

回答済み
How to model Concave Hull Contact Force in Simulink Simscape
For a generic solid, Multibody only support exporting the Convex Hull for contact modeling (as of R2025a). So that quarter pipe...

29日前 | 0

回答済み
how to understand and combine simscape pump performance curves
I can try to help on the "Plotting on the Same Graph" part. Once you generate this figure from the pump block, you can use the ...

約1ヶ月前 | 0

| 採用済み

回答済み
LNG liquid to gas phase change simulation Simscape
Hi @Anil I suggest that you try something like this: Model the LNG and its evaporization in the 2P domain. The Receiver Acc...

約1ヶ月前 | 1

| 採用済み

回答済み
What is my fault to this modelling? I want to move the model but I am not able to solve the faults.
Follow the instructions in the error message. Use the Simulink-PS Converter to provide derivatives. The time constant will c...

約2ヶ月前 | 0

回答済み
Modelling the sublimation of dry ice
Hi @Kyle, Interesting problem. I would approach it from the angle of convervation of energy and mass. Assuming the dry ice st...

約2ヶ月前 | 2

| 採用済み

回答済み
How to model a piston with a retracting spring at one end and having single hydraulic port??
Something like this should work. It's important to pay attention to a few things when setting up this model: (1) area of the...

約2ヶ月前 | 0

回答済み
Implementing Process Control for Heat Exchanger Networks in MATLAB
For the physical plant, for instances heat exchangers, pipes, valves, pumps, etc., I suggest that you look into Simscape and Sim...

約2ヶ月前 | 0

回答済み
Lead screw driven by a revolute joint in Simscape Multibody: How can I set a slider displacement to be proportional to the revolute joint angle?
Hi @mhaz, I think it would make more sense to move the revolute joint to be in series with the prismatic joint. See below. ...

約2ヶ月前 | 0

回答済み
How to measure torque and rpm of compressor in refrigeration cycle?
Use a Ideal Torque Sensor, connect it in series with the compressor R port, and now you are measuring the shaft torque. Multipl...

3ヶ月前 | 0

回答済み
How to plot coefficient of performance(COP) of refrigerationcyclemodelexample?
For an air conditioning system, the COP is defined as the ratio between the cooling power and the compressor work. There are tw...

3ヶ月前 | 0

回答済み
MATLAB Projects for Mechanical Engineers
Hi Saurav, A few things to check out on fileexchange: Ivan Liebgott (2024). Modeling and Simulation of Multi-Physics Systems w...

3ヶ月前 | 0

回答済み
Network coupler for gas
Network coupler for Gas or Moist Air domain doesn't exist as of R2024b. I see two options: (1) follow the structure of such co...

3ヶ月前 | 0

| 採用済み

回答済み
How are centrifugal pump(TL) outlet flow rate and actual brake power calculated with pump nominal parameters?
In the equation for the reference capacity: , the first term on the RHS is the volumetric flow rate. If you move that term t...

3ヶ月前 | 0

| 採用済み

回答済み
I don' know why simulink parameter estimation failed. Please help me
Looks like the error message is trying to tell you that the Parameter Estimater cannot change the parameters it tries to estimat...

3ヶ月前 | 1

| 採用済み

回答済み
How can I determine the distance at which a moving frame slides over a fixed frame, knowing that I use a prismatic joint between these two frames?
You can set limits in the prismatic joint. It'll apply an additonal spring & damper once the limit is reached and try to stop t...

4ヶ月前 | 0

回答済み
How to change the type of step for a Simulink Solver from variable to fixed in the Electric Vehicle Thermal Management model in Simulink?
When trying to run a complex Simscape in fixed-step, it is almost always recommended to use an implicit solver, as the equations...

4ヶ月前 | 0

回答済み
How to change a simscape block parameter from MATLAB app?
modelname = "myModel"; % CHANGE THIS refrigerant = "R134a"; % CHANGE THIS. % You may use any of the following refrigerant n...

4ヶ月前 | 1

| 採用済み

回答済み
How to obtain 4th order transfer function in simulink
This example from the System Identification Toolbox should address what you need. https://www.mathworks.com/help/ident/ug/estim...

4ヶ月前 | 0

回答済み
How to visualize a multibody model when running on a Speedgoat
Hi @f wang, If I understand it correctly, you are trying to visualize the 3D movements of the parts, is that right? If so, the...

4ヶ月前 | 0

| 採用済み

回答済み
Is there a way to add a graphical only line between two frames in multibody
Hi Mark, I don't think there is a "native" way to do this. I can think of a clunky way of doing this. I don't like it but may...

4ヶ月前 | 0

回答済み
Determining the Nominal mass flow rate
Hello, First of all, make sure you follow the workflow example in the documentation when modeling a refrigeration system: https...

4ヶ月前 | 0

さらに読み込む

Yifeng Tang

MathWorks

統計

MATLAB Answers

MATLAB Answers

MATLAB Answers

File Exchange

MATLAB Answers

File Exchange

File Exchange

MATLAB Answers

MATLAB Answers

Feeds