Yifeng Tang

MathWorks

Last seen: Today | 2020 年からアクティブ

Followers: 1 Following: 0

Programming Languages:
Python, MATLAB, Fortran
Spoken Languages:
English, Chinese
Pronouns:
He/him
Professional Interests:
Physical Modeling, Simscape Fluids, Simscape, Heat and Mass Transfer, Thermodynamics and Heat Transfer

統計

All

バッジを表示

Feeds

回答済み
Challenge with Simulating Loader Mechanism with Closed Kinematic Loop
Hi @Medalan Thanks for the clarfication on your question. Let's see if this idea helps. I created two simple models to demons...

5日前 | 0

| 採用済み

回答済み
Signal Routing in Simscape
Hi Paul, I think we can achieve what you envisioned not with a switch of joints but with a "hard-stop". I created a 1D Simscap...

5日前 | 0

回答済み
Jacobians using Simscape (numerical or symbolic)
The Jacobian of the system of equations is formulated by the solver, but I don't think it's available explicitly in any form. I...

5日前 | 0

回答済み
Inputs and process for thermal model discretization for battery spatial temperature estimation
If you are thinking about running the ANSYS simulation and Simscape at the same time, with some kind of interface to pass along ...

5日前 | 0

回答済み
How to model the battery module with forced air cooling in Simscape?
Something like this should work. Well, reasonable parameters are really what will make it work :)

10日前 | 0

| 採用済み

回答済み
[Thermal Liquid library Simscape] Help for an Engine cooling model
Copied from the comment section: I changed pressure_sidepods from 500 to 2000 and did observe change in the coolant temperature...

16日前 | 0

回答済み
Direction of force input for a prismatic joint
Yes, you are correct. When you provide a negative value for the actuation force, it's applied in the opposite direction with th...

24日前 | 0

| 採用済み

回答済み
How to create a Simscape custom component with 2 different thermal liquids?
Hi Jérémie, The error was complaining about that two stream of fluids are mixing into each other inside your heat exchanger :p ...

27日前 | 2

| 採用済み

回答済み
How do I get the right vector of spring coefficients for the nonlinear translational spring?
Hi Emefun, A couple of things to fix: (1) add mass blocks. The "dynamic variable derivatives" error is most likely referring ...

約1ヶ月前 | 0

| 採用済み

回答済み
Are Flooded Evaporators modeled already?
Hi Pablo, To the best of my knowledge, there isn't a block designed specifically for this type of heat exchanger, with coolant/...

約2ヶ月前 | 1

| 採用済み

回答済み
Add "Block Parametrization Manager" to custom ssc block for Simscape
It's not supported for your use case here. Consider put together a custom Simulink library instead, where you can store and loc...

約2ヶ月前 | 0

| 採用済み

回答済み
Simulation of two phase fluid with Simscape - pressure behavior unexplicable
Hi Marcel, The port area parameter of the Receiver Accumulator block doesn't affect the pressure drop between inside and outsid...

約2ヶ月前 | 0

回答済み
MATLAB/Simulink/Simscape:Contact force analysis
You can only to "Convex Hull" for generic geometry (e.g. a stp file). It may or may not be good enough for your contact force m...

2ヶ月前 | 0

| 採用済み

回答済み
The Excavator Hydraulic Jack Forces are Changing Direction in Simscape Multibody
The way the joints are actuated and the joint forces are sensed for inverse dynamic analysis looks OK. As a position signal is ...

2ヶ月前 | 1

| 採用済み

回答済み
Fluid inertia in Simscape hydraulic
Hi Amodio, I don't think the actuator blocks model the inertia of the fluid inside. The "cushion" can be used to model some en...

2ヶ月前 | 0

回答済み
Center of mass of a free-floating body in Simscape Multibody is moving with no external forces
I believe there can be many solutions that would satisfy the initial conditions you have set. The only target set here is the s...

2ヶ月前 | 0

| 採用済み

回答済み
Flow rate discrepancy between upstream and downstream of orifice model.
A diffential pressure 2950 psi sounds big enough to change the density of the fluid. As the density changes, volumetric flow ra...

2ヶ月前 | 0

回答済み
Simscape Fluids model of closed system
Hi Jeremy, Looks to me like an initialization issue. I don't have R2020b on my computer so I tried this on R2021b, the oldest ...

2ヶ月前 | 0

回答済み
How to make a revolute joint turn in one direction in Simscape?
There may be better solutions, but just some ideas. If you have access to Simscape Driveline, there is a one-way clutch (Unid...

2ヶ月前 | 0

回答済み
Pressure drop of a two-phase fluid pipeline in simscape
You can view the Simscape code of the Pipe (2P) block, save a copy, and modify it to use a custom correlation if you like. Find...

2ヶ月前 | 0

| 採用済み

回答済み
Can "pipe(G)" block be used to model forced air convection?
I think it's possible. The combination of cross section and hydraulic diameter will give you a circumference; that multiplied b...

2ヶ月前 | 0

| 採用済み

回答済み
HOW CAN I TURN AN EQUATION INTO COMPONENT IN A LIBRARY?
Hi Usha, In addition to Ayush's answer, I suggest that you look at the source code of a translational spring block. You custom...

3ヶ月前 | 1

回答済み
How does simscape caculate the hydraulic pressure?
The pump blocks in Simscape Fluids models the flow rate at different pressure difference and speed, but themselves are "volume-l...

3ヶ月前 | 0

回答済み
state flow入门之旅中的诸多疑问
应该是workspace的问题，红色阴影表示有缺失的参数值。Simulink模型的参数可能在 Base Workspace, Model Workspace 或者是 mask local workspace (你这里不会是最后这个情况)，可以参考这个文档：...

3ヶ月前 | 0

回答済み
Use Simscape parameter as variable in Simulink model
If it's in the Simscape Results Explorer, you should be able to use a Probe block to make it available during simulation as a Si...

3ヶ月前 | 0

回答済み
Using the TL-2P heat exchanger in simscape to simulate an external threaded tube heat exchanger
The way you set up the heat exchanger looks promising to me. I would use the Parameter Estimator App (Documentation) to estimat...

3ヶ月前 | 0

| 採用済み

回答済み
why are the results different from moist air domain(MA) using only dry air and gas domain(G)? - simscape
Hello, Given the range of temperature you'd like to implement, I believe you are seeing the difference in the way the specific ...

3ヶ月前 | 1

回答済み
The sum of the 2 branches flow is different than pump flow
Hi Flavio, I looked at the model and below are my observations. the parameters and inputs for the pump look ridiculous: at 1m^...

3ヶ月前 | 2

| 採用済み

回答済み
Simscape 4-Way 3-Position Directional Valve (IL) No "Fluids/Plot Valve Characteristics" Option
See the comment section for the discussion. Issue resolved (by itself) as of now.

3ヶ月前 | 0

回答済み
Pipe (TL) fluid compressibility problem
See this related question for a more detailed discussion: https://www.mathworks.com/matlabcentral/answers/2111661-rservoir-tl

4ヶ月前 | 0

| 採用済み

さらに読み込む

Yifeng Tang

MathWorks

統計

MATLAB Answers

MATLAB Answers

File Exchange

MATLAB Answers

File Exchange

File Exchange

MATLAB Answers

MATLAB Answers

Feeds