Community Profile

photo

madhan ravi


Last seen: 2日 前 2018 年からアクティブ

BMW BMS MBD (Automotive). Absolute fan of MathWorks.

Spoken Languages:
English, German

統計

All
  • Master
  • First Review
  • First Submission
  • Thankful Level 5
  • 12 Month Streak
  • Knowledgeable Level 5
  • Promoter
  • Commenter
  • Revival Level 3
  • Solver
  • First Answer

バッジを表示

Content Feed

表示方法

回答済み
Referenced model contains an algebraic loop. Referenced models do not support algebraic loops
As seen in the preview of the Referenced Model, there is a feedback to a subsystem make sure to add a Unit Delay block to the fe...

約2ヶ月 前 | 0

| 採用済み

回答済み
Using multiple instances of a referenced model with different port dimensions
Seems like there is no way to do what you want using a *Referenced Model* AFAIK. I would rather suggest you to make the model as...

約2ヶ月 前 | 0

回答済み
I am facing problem when I am using frequency analyzer in Simulink.
Continuous Sample Time

約2ヶ月 前 | 0

回答済み
How to activate Interpolate Data in Inport block in Simulink MATLAB
That option is under Execution dialog box:

約2ヶ月 前 | 0

回答済み
How can I avoid errors due to division by zero in Simulink?
Or making the result to be zero when the divisor is zero using a *Switch block*

約2ヶ月 前 | 0

回答済み
Adding text to a plot without specifying it first as a string
r = 1:3; rho = 4:6; plot(1:10) x = 1:3:9; y = x+1; for k = 1 : numel(x) text(x(k), y(k), {"r = " + r(k), "\rho = " + r...

約2ヶ月 前 | 0

| 採用済み

回答済み
Why does my top bar flicker and grays out in Simulink?
Perhaps a bug report to *MathWorks Support Team*?

約2ヶ月 前 | 0

回答済み
how to run Model predictive controller in parallel with another model
You probably need <https://in.mathworks.com/help/simulink/model-reference.html>

約2ヶ月 前 | 0

| 採用済み

回答済み
Simlink example “Heat Conduction Through Iron Rod”
*From Left to Right :* T_5 is To Workspace block it is connected to Demux block which is connected to Scope. Cyl 2 (not ent...

約2ヶ月 前 | 1

| 採用済み

回答済み
Get data points for simscape-Table based battery
https://in.mathworks.com/help/sps/ug/pre-parameterized-components.html#mw_e92af2d2-0ae5-4856-af2b-9b386e72860f here you can find...

約2ヶ月 前 | 0

| 採用済み

回答済み
Why i can not connect current sensor to dc voltage?
You need <https://in.mathworks.com/help/simscape/ref/simulinkpsconverter.html#:~:text=The%20Simulink%2DPS%20Converter%20block,a%...

約2ヶ月 前 | 0

| 採用済み

回答済み
Good day, i designed a model whereby if the speed of the drive profile is less than zero,the output should be one.
If you have the drive cycle as a .mat file, use a *From File* block.

約2ヶ月 前 | 0

回答済み
How to export a matlab/simulink model to FMU
https://in.mathworks.com/help/slcompiler/gs/export-simulink-models-to-functional-mock-up-units.html#mw_b6804c90-9242-4064-a65e-8...

約2ヶ月 前 | 0

回答済み
Keyboard Shortcut ctrl+d (init model) - does not work any more
what do you mean init model? https://in.mathworks.com/help/simulink/ug/summary-of-mouse-and-keyboard-actions.html#butxv7y it is...

約2ヶ月 前 | 0

回答済み
Difference between Matlab, simulink and embedded coder?
https://in.mathworks.com/matlabcentral/answers/12091-difference-between-simulink-coder-embedded-coder-and-matlab-coder https://...

約2ヶ月 前 | 0

回答済み
How to phase shift a non sinusoidal signal in Simulink
One would need to use Phase Locked Loop ( PLL ) to determine the phase angle of the signal and then you can phase shift the ang...

約2ヶ月 前 | 0

回答済み
I integrated fault current which is sine wave with its time period as an interval. But, i am getting value as an answer instead of getting 0.
Not sure what you are doing with your code. When using cursor measurements the 2 cursor points should measure same value as 0. D...

約2ヶ月 前 | 0

| 採用済み

回答済み
Too many output arguments. Requested 3 output(s), but only 1 output(s) available.
You expect three outputs to be returned from sim() whereas only one output can be returned from sim() command <https://in.mat...

約2ヶ月 前 | 1

| 採用済み

回答済み
Get timescale for all layouts in Simulink Scope
<https://in.mathworks.com/help/simulink/slref/spbscopes.scope.timescopeconfiguration.html#buvw6zv-1-TimeAxisLabels *TimeAxisLabe...

約2ヶ月 前 | 1

回答済み
Why are the Corners Shaded in the Model Reference Block?
https://in.mathworks.com/help/simulink/slref/visualizing-model-reference-architectures.html when SimulationMode is in Accelerato...

約2ヶ月 前 | 0

| 採用済み

回答済み
Struct as mask input
Use one of the approaches mentioned in the link: https://in.mathworks.com/matlabcentral/answers/2050862-how-to-pass-a-struct-to...

約2ヶ月 前 | 0

回答済み
two output in one scope
Using 2 Model Blocks reference one .mdl file and and the other .mdl file (if the model block doesn"t support .mdl format, conver...

約2ヶ月 前 | 1

回答済み
why matlab can't plot signals ?
t = 0 : 0.0001 : 0.1; % ^

約2ヶ月 前 | 1

回答済み
finding the columns include ones
index = find(all(matrix)) % one can directly use logical indexing without find() function

約2ヶ月 前 | 0

| 採用済み

回答済み
I have plotted a signal in Simulink and now i want to write a code to integrate that signal over the limits? can anyone help me with this please
Use Integrated Limited block specifying the upper limit as 0.008 and lower as 0. edit: Thanks @Paul, i overlooked it, yes the s...

約2ヶ月 前 | 1

| 採用済み

回答済み
Concatenating vector in in simulink for loop
You need to use <https://in.mathworks.com/help/simulink/slref/assignment.html?searchHighlight=Assignment%20block&s_tid=srchtitle...

約2ヶ月 前 | 0

回答済み
SIMULINK char to num
receivedData = [49 50 51 46 52 53 54 55 32 32 32 32 32 32 55 54 53 46 52 51 50 49 32 32 32 32 32 32 32 32 32 32 32 32 32 49 32 3...

約2ヶ月 前 | 1

| 採用済み

回答済み
Hi Any one knows how to interface delta VFD MS300 with matlab to control motor speed and direction.
I was not able to find an example where VFD MS300 was interfaced but there are several examples of controlling Motors using MATL...

2ヶ月 前 | 0

回答済み
I am a 3rd year ECE UG student i know the basics of this matlab language but want to from the community about how to get advanced.....
<https://in.mathworks.com/help/overview/wireless-communications.html#:~:text=Wireless%20engineering%20teams%20use%20MATLAB,over%...

2ヶ月 前 | 1

回答済み
How to find the gradient of plotted values?
Derivative at the local maximum is zero. You could find the gradient of a variable using doc gradient

2ヶ月 前 | 0

さらに読み込む