photo

Karunya Choppara

Last seen: 約1ヶ月 前 |  2020 年からアクティブ

Followers: 0   Following: 0

統計

  • Knowledgeable Level 2
  • Revival Level 2
  • First Review
  • First Answer

バッジを表示

Feeds

表示方法

回答済み
Radar experiment using two USRPs
MIMO cable synchronization for USRP N210 radios is available in R2024b release MATLAB with Communications Toolbox Support Packag...

3ヶ月 前 | 0

回答済み
IS CONFIGURING TWO USRPS THROUGH MIMO CABLE TO A SINGLE PC SUPPORTED IN MATLAB
MIMO cable synchronization for USRP N210 radios is available in R2024b release MATLAB with Communications Toolbox Support Packag...

3ヶ月 前 | 0

回答済み
support usrpN210 with mimo cable
MIMO cable synchronization for USRP N210 radios is available in R2024b release MATLAB with Communications Toolbox Support Packag...

3ヶ月 前 | 0

回答済み
How do I set the clock and time references of USRP to external reference or to MIMO cable for a secondary USRP?
MIMO cable synchronization for USRP N210 radios is available in R2024b release MATLAB with Communications Toolbox Support Packag...

3ヶ月 前 | 0

回答済み
USRP Device N210 mimo cable support
MIMO cable synchronization with USRP N210 radios is available in R2024b release MATLAB

3ヶ月 前 | 0

回答済み
GPS time extraction using GPSDO module for USRP N210
GPS with receive timestamps is supported with R2022a MATLAB release.

3ヶ月 前 | 0

回答済み
In Communication Toolbox Support Package for USRP Radio, how to synchronize Tx and Rx time stamps to achieve true full-duplex?
Trigger time based transmit and receive is supported with MATLAB in R2023b. To get the latest version of MATLAB check the page h...

約1年 前 | 0

回答済み
How do I set the clock and time references of USRP to external reference or to MIMO cable for a secondary USRP?
GPSDO support is available with USRP Hardware Support Package since R2021a. Both External or GPSDO Clock Source and PPS source...

約1年 前 | 0

回答済み
USRP Codegen error : Nontunable property 'ChannelMapping' may only be assigned once.
Here the property 'ChannelMapping' of system object comm.SDRuReceiver is a non tunable property, and cannot be changed in betwee...

約1年 前 | 0

| 採用済み

回答済み
How to setup N321?
Please follow the steps detailed on this page https://in.mathworks.com/help/supportpkg/usrpradio/ug/configuring-host-computer-f...

1年以上 前 | 0

回答済み
USRP B210 communication using OFDM
Hi As the sample rate is 20e6, the packet errors could be due underruns and overruns during transmit and receive https://in.ma...

2年以上 前 | 0

回答済み
Connect two or more USRPs
This issue is with UHD 3.15 and the issue is resolved in the latest version of UHD, which is 4.1.0.4. MATLAB release R2022a use...

2年以上 前 | 0

回答済み
SNR of a USRP in Simulink
Here is a steps to find the SNR Obtain the noise power, by measuring the input power when there is no transmitted signal. Mak...

3年弱 前 | 0

回答済み
Hi, I am using USRP NI 2920. By using findsdru ('192.168.10.2') .I am Unable to do real-time signal transmission in MATLAB
Hi, You will still be able to use the device successfully for USRP transmit receive operations. Please ignore this error messa...

3年弱 前 | 0

回答済み
Getting timestamp from Ettus USRP X300 series
Hi, Time stamps for USRP is supported in R2022a, that is currently available as pre-release. The support package for pre-relea...

3年弱 前 | 0

| 採用済み

回答済み
Lossless real-time signal acquisition from USRP 2955
Hi, The increase in time doesn't indicate data loss during acquisition. The losses in acquisition will be indicated using the...

約3年 前 | 0

| 採用済み

回答済み
How to extract two signals from two different USRP devices connected with MIMO expansion cable?
Hi You can set a new IP address to the N210 radio using setsdruip function, as described on this page https://in.mathworks.co...

3年以上 前 | 0

| 採用済み

回答済み
Transmission and Reception through USRP B210
Hi You can take a look into the frequency calibration example, that transmits and receives a Sine wave using USRP https://in....

3年以上 前 | 0

回答済み
N210 buffering problems
Hi Magnus The buffer mechanism for SDRu Transmitter and Receiver system objects is updated in R2021b, that are now available wi...

3年以上 前 | 0

回答済み
Can't connect to USRP N321(or N310)
Hi Please follow the Recommended action and click on "Assign IP Address" button, and you should be able to see the detection re...

3年以上 前 | 0

回答済み
N210 buffering problems
Hi Magnus, One trick would be to use burst mode with number of frames in burst set to 1. https://in.mathworks.com/help/suppor...

3年以上 前 | 0

回答済み
USRP N210 / B210
In R2021a the support for GPSDO as ClockSource and PPSSource is provided, from SDRuReceiver and SDRuTransmitter system objects i...

3年以上 前 | 0

回答済み
why do i get zero vector when using USRP N210 with MATLAB using comm.SDRuReceiver ?
When len = 0, the data from radio() call is not a valid data, and we see all zeros in the rxSig output. When providing data to ...

3年以上 前 | 0

| 採用済み

回答済み
N210 buffering problems
The dummy data indicates that the data is not valid. If the data length output of the SDRuReceiver is greater than zero, it indi...

3年以上 前 | 0

回答済み
How to set the 4 Rx channel of USRP X310
The 4 channel support for TwinRx daughterboard with X300 and X310 is enabled in R2020a release.

4年以上 前 | 0

| 採用済み