パッチ アンテナ

Model Coaxial Gap Feed for Probe-Fed Patch Antenna

Comparison of a standard delta-gap probe feed model and a finite-gap coaxial feed model for a patch antenna.

Miniaturize Rectangular Microstrip Patch Antenna Using Genetic Algorithm Optimization

Miniaturize rectangular microstrip patch antenna using genetic algorithm (GA) optimization.

Artificial Intelligence (AI) for Rapid Analysis and Design of Patch Antenna

Use artificial intelligence (AI) to rapidly analyze and design antennas from the Antenna Toolbox™ catalog.

Train Machine Learning Model for Analysis of Custom Antenna

Apply machine learning to antenna analysis: a general recipe that you can use to train machine learning models to characterize antenna structures modeled and simulated in Antenna Toolbox™.

Sensitivity Analysis for Antenna Using Monte-Carlo Simulation

Sensitivity analysis of microstrip patch antenna gain using design space sampling.

Design and Simulate Monopulse Tracking System

Model and simulate a monopulse tracking system with a transmitter antenna, receiver antenna, and comparator.

(RF Blockset)

Analysis of Ultrawideband Trident Inset-Fed Monopole Antenna with Conical Ground

Design trident inset-fed monopole antenna using 3-D modeling features and analyze its performance over a conical ground plane.

Dual-Fed Square Microstrip Patch Antenna for BLE Applications

Design and analyze the dual-fed square microstrip patch antenna for Bluetooth Low Energy applications.

(RF PCB Toolbox)

Corporate Feed Divider Network for a Linear Patch Antenna array

Integrate a corporate power divider with a microstrip patch antenna array. The corporate power divider is available as a catalog element in RF PCB Toolbox. The patch antenna array is built using the patchMicrostripInsetfed catalog element and pcbStack from Antenna Toolbox.

(RF PCB Toolbox)

Design S-Band Monopulse Tracking Radar Antenna

Design a 3‑GHz S‑band monopulse tracking radar antenna by integrating a 2×4 microstrip patch array with a rat‑race coupler, and validate its performance through simulated and measured results.

ISM Band Microstrip Patch Antennas and Mutually Coupled Patches

Design and analyze rectangular, circular, triangular and elliptical microstrip patch antennas operating in the ISM (Industrial Scientific and Medical) band 2.4 GHz - 2.5 GHz. In the second half, this example shows how to create an array of rectangular and triangular patch antennas, and gauge the effect of mutual coupling on its radiation pattern. This array configuration has lowest coupling among these ISM band patch antennas.

Patch Antenna with Dielectric Substrate

Calculates the performance of two linearly polarized patch antennas.

Design PIFA for WLAN Wi-Fi Applications

This example designs a PIFA for wireless applications.

Polarization Analysis of X-band Microstrip Patch Antenna

Perform polarization analysis on a microstrip patch antenna with the air substrate. The dimensions of this antenna are referenced from [1] for the center frequency of 10.35 GHz. In most basic form, a microstrip patch antenna consists of a radiating patch on one side of a dielectric substrate and a ground plane on the other side. Microstrip patch antennas radiate primarily as wide open-open half-wave microstrip resonators. The length L of the rectangular patch for the fundamental excitation mode is slightly less than $$\lambda$$/2. For a good antenna performance, a thick dielectric substrate having a low dielectric constant is usually desired since it provides a larger bandwidth and a well-defined beam. A rectangular microstrip patch antenna normally radiates a linearly polarized wave with about 6-7 dBi gain at broadside. Higher gains (up to 10 dBi) can be achieved by using different means including large patch heights and parasitic patches.

Analysis of Inset-Feed Patch Antenna on Dielectric Substrate

Showcases the analysis of an inset-feed patch antenna on a low-epsilon, low-loss, thin dielectric substrate. The results are compared with the reflection coefficient and surface currents around the 2.4 GHz, Wi-Fi band for a reference design [1]. The Antenna Toolbox™ library of antenna elements includes a patch antenna model that is driven with a coaxial probe. Another way to excite the patch is by using an inset-feed. The inset-feed is a simple way to excite the patch and allows for planar feeding techniques such as a microstrip line.

Design, Analyze, and Prototype 2-by-2 Patch Antenna Array

Design and analysis of a 2‑by‑2 microstrip patch antenna array on an FR4 substrate operating at 2.4 GHz, including full simulation and generation of PCB Gerber files for fabrication.