photo

Nick Choi

Last seen: 約1ヶ月 前 |  2017 年からアクティブ

Followers: 1   Following: 0

統計

All
  • Knowledgeable Level 4
  • Knowledgeable Level 3
  • Solver
  • First Review
  • 3 Month Streak
  • First Answer

バッジを表示

Feeds

表示方法

回答済み
Developing a Matlab docker container which can run Matlab 2012 versions
Based on the info in the post, it sounds like you are planning to add MATLAB Integration for Jupyter to your JupyterHub - is tha...

3ヶ月 前 | 0

回答済み
Rapid Accelerator Mode fatal error C1128
You can add '/bigobj' to the compiler options in the 'Code Generation' pane of the 'Configuration Parameters' in Simulink to a...

約7年 前 | 2

| 採用済み

回答済み
PWM generation - triangle carrier problem
It is tough to say without a reproduction model but this could be due to differing sample times between the two signals going in...

約7年 前 | 0

回答済み
generating square wave to control a motor without using simulink
The 'writePWMDutyCycle' function in the MATLAB Support Package for Arduino would allow you to control the duty cycle/pulse width...

約7年 前 | 0

回答済み
change the modulation in commrfsatlink
The following section of the example page provides information on how some of the model's parameters can impact the performance ...

約7年 前 | 0

回答済み
using a table in a "from workspace block" in simulink
If the data is loaded into MATLAB as a table, you could import the signal data using a 'From Workspace' block on the column or r...

約7年 前 | 0

回答済み
Update a fixed dimension vector Simulink
A block that may be helpful for this could be the 'Assignment' block: <https://www.mathworks.com/help/simulink/slref/assignme...

約7年 前 | 0

| 採用済み

回答済み
I have no idea how to do this simulink, please help
Figure 1 shows you what the model should look like so you essentially just need to reconstruct that model in Simulink. This ...

約7年 前 | 0

回答済み
What is the computation Power of Matlab Online?
The following documentation pages should help give you a better idea of what tasks can be performed using MATLAB Online. Thi...

約7年 前 | 0

回答済み
Simulink Real Time/Simulink Test using National Instruments RT hardware?
Simulink Test allows you to develop and execute simulation-based tests for your Simulink models and these tests can be run with ...

約7年 前 | 0

回答済み
Use of soundcard in Simulink!
The 'Audio Device Reader' block in the Audio System Toolbox would allow you to read audio from your computer's sound card. The f...

約7年 前 | 0

| 採用済み

回答済み
How do i create a simplified version of a continuous time unit step function?
The following example shows how to create a variety of signals such as the unit impulse, unit step and unit ramp signals: <ht...

約7年 前 | 0

回答済み
How to input a signal to a Simulink Function within a Stateflow Chart?
Based off of the error message, it seems as though the function call block is set to have a sample time of zero. Since the input...

約7年 前 | 0

回答済み
Implementing neural network functions on HDL
The following documentation page provides a list of the MATLAB functions that are supported for HDL code generation: <https:...

約7年 前 | 1

| 採用済み

回答済み
Activate a pulse generator from an if block
You could use a 'Compare to Constant' block to compare the signal/variable against the specified value and this could be used to...

約7年 前 | 0

回答済み
Difficulty using the CWT function
It seems as though the error messages are being generated because the new and old versions of the 'cwt' function are being calle...

約7年 前 | 0

回答済み
How can I find Model-Based Calibration Toolbox in MATLAB 2017b?
Is 'Model-Based Calibration Toolbox' displayed when you execute the following command? >> ver If it is not displayed by...

約7年 前 | 0

| 採用済み

回答済み
Missing simscape power systems
Is 'Simscape Power Systems' displayed when you execute the following command? >> ver If it is not displayed by the 'ver...

約7年 前 | 1

回答済み
Simulink name logged runs
You can name a run with a string to facilitate data inspection by utilizing a function call similar to this one: Simulink.s...

約7年 前 | 0

回答済み
How to model a slack(swing) bus in simuilink model?
The 'Load Flow Bus' block can be used to specify the parameters of a swing bus: <https://www.mathworks.com/help/physmod/sps/pow...

7年以上 前 | 0

回答済み
How to solve "No rule to make target `rtiostream_utils.c' " error while building model in Simulink?
Without a reproduction model or screenshots of the entire error, it is somewhat difficult to determine a potential root cause. H...

7年以上 前 | 0

回答済み
How can I pass a Figure Handle to Matlab code embedded in Simulink, and capture that plot as an Image in the loop?
If you are planning to generate code from the Simulink model, you will not be able to use the 'plot' function because it is not ...

7年以上 前 | 0

回答済み
R2017b Visual Studio 2017 can't link model files when compiling simulink
This issue seems like it may be related to the following external bug report: <https://www.mathworks.com/support/bugreports/1...

7年以上 前 | 0

| 採用済み

回答済み
Understanding usrpe3xxToneReceiverML.m example
In the 'Transmit a Tone Signal from the FPGA' section of the example, there is a line that says "Note that the simultaneous tran...

7年以上 前 | 0

回答済み
I have successfully generated the code from the matlab, but I don't kown how to use these codes in the embedded equipment.
When you generate C/C++ code through MATLAB Coder, you can specify the target platform for the code and you can configure it to ...

7年以上 前 | 0

| 採用済み

回答済み
put coodinate in image map
The following documentation page provides an example of how to display topographic data in MATLAB: <https://www.mathworks.com/h...

7年以上 前 | 0

| 採用済み

回答済み
How can I force a Custom Storage class for a parameter inside StateFlow?
If you are looking for how to use custom storage classes or custom data types in Simulink, the following documentation link prov...

7年以上 前 | 0

回答済み
Hou to make a simulink lookup table model for different break point?
Simulink comes with several shipped lookup table blocks. The following documentation page contains a list of the various lookup ...

7年以上 前 | 0

回答済み
How can explain the relation between mdlDerivatives output and mdlOutputs in S-function simulink
As described in this documentation link, 'mdlDerivatives' is an optional method that can be used to compute the derivatives for ...

7年以上 前 | 1

回答済み
How do I use a discrete-time state-space model inside simulink?
If you want to implement a discrete-time state-space model in Simulink, you can use the 'Discrete State-Space' block. The follow...

7年以上 前 | 0

さらに読み込む