Matlab considers different two equal numbers!

7 ビュー (過去 30 日間)
Mohammad
Mohammad 2019 年 12 月 6 日
編集済み: Adam Danz 2019 年 12 月 10 日
I calculated a matrix (attached). In the 11th row, matlab considers the 3rd column, i.e., entry (11, 3) as the maximum entry of the that row, although, the entries in columns 1, 2, ..., 7, and 15 have the exact same value, i.e.,
find(matrix(11, :) == max(matrix(11, :)))
only gives 3.
Does anyone know why it happens?
Thanks

回答 (2 件)

Star Strider
Star Strider 2019 年 12 月 6 日
You are not seeing the entire picture.
If you test ‘matrix(11,:)’:
Check = matrix(11, :) - max(matrix(11,:))
the result is:
Check =
-0.000000000000006 -0.000000000000002 0.000000000000000 -0.000000000000007 -0.000000000000003 -0.000000000000004 -0.000000000000002 -0.500000000000002 -0.999999999999997 -1.499999999999993 -1.999999999999991 -1.499999999999994 -1.000000000000000 -0.500000000000006 -0.000000000000003
and you have encountered ‘floating-point approximation error’.
See the documentation section on Floating-Point Numbers for an extended discussion.
  7 件のコメント
Star Strider
Star Strider 2019 年 12 月 9 日
@Walter —
Thr original Question was about floating-point approximation error. I considered ismembertol for the comaprisions, however this Comment introduces some ambiguity with respect to the what Mohammad wants. Apparently, Mohammad wants 4-digit precision everywhere. That may not be possible because certain operations would inevitably result in extended precision results that would again need to be truncated.
Walter Roberson
Walter Roberson 2019 年 12 月 10 日
But what I want MATLAB to do is to force it do all the calculations only by considering 4 digits after decimal point.
Use the Fixed Point Designer product; https://www.mathworks.com/help/fixedpoint/

サインインしてコメントする。


Adam Danz
Adam Danz 2019 年 12 月 9 日
編集済み: Adam Danz 2019 年 12 月 10 日
You could limit the values in your matrix to the first 4 decimal places but this is usually not a good idea unles there's a reasonable justification to do so. Take a look at the values you mentioned.
format long % so you can see more decimal places
Trace_Wc([1,2,7],3)
ans =
1.249999999999995
1.250000000000014
1.249999999999999
As you can see, limiting those values to the first 4 dp will not give you matching values.
Those same values in "short" format are
format short
Trace_Wc([1,2,7],3)
ans =
1.2500
1.2500
1.2500
But the key point is that the format just affects what you see, not the actual values.
If you have principled reason to truncate the precision to 4 decimal places (ie, the instrument used to get the data is only precise to 3 dp), you could do so like this:
Trace_WcNew = round(Trace_Wc, 4);
% Trace_WcNew = round(Trace_Wc * 1E4)/1E4 % for <r2014b (see comments below)
Instead, if you're trying to find values in a row that are approximately equal to the max value of that row, use a threshold like this:
idx = abs(Trace_Wc(11,:) - max(Trace_Wc(11,:))) < 0.0001
This locates all values in row 11 that are within 0.0001 of the max. Here's what it's returns:
format long
Trace_Wc(11,idx)
ans =
Columns 1 through 6
2.249999999999984 2.249999999999988 2.249999999999990 2.249999999999983 2.249999999999988 2.249999999999987
Columns 7 through 8
2.249999999999988 2.249999999999988
In that case, 0.0001 is somewhat arbitrarily chosen after looking at the data. Instead, you could use a threshold that is 1/10 of 1% of the range of your data such as
threshold = range(Trace_Wc(11,:))*.001
  2 件のコメント
Walter Roberson
Walter Roberson 2019 年 12 月 9 日
Trace_WcNew = round(Trace_Wc * 1E4)/1E4
These days,
Trace_WcNew = round(Trace_Wc, 4);
Adam Danz
Adam Danz 2019 年 12 月 9 日
Jeez... that's been out since r2014b and I keep forgetting to use it.... thx Walter.

サインインしてコメントする。

カテゴリ

Help Center および File ExchangeLogical についてさらに検索

タグ

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by