photo

Yusuf Selim KARATAS


Last seen: 3年弱 前 |  2019 年からアクティブ

Followers: 0   Following: 0

統計

  • Thankful Level 1
  • Knowledgeable Level 1
  • First Answer
  • First Review

バッジを表示

Feeds

表示方法

質問


SIMSCAPE Parameters from WorkSpcae
Dear All, I have a simscape model that has some parameters like SOC_points, T_points and C points. I enter cell_SOCpoints, cell...

3年以上 前 | 0 件の回答 | 0

0

回答

質問


Version Control for slx Files
Dear All, We are currently using Version Control systems in our project on Matlab. Our project has .slx files and since .slx ...

3年以上 前 | 0 件の回答 | 0

0

回答

質問


PROCESSOR IN THE LOOP - DATA PAYLOAD
Dear All, I am working on NXP S32K144 with MBD tools. What I am trying to is implementing Processor in the Loop Simulation with...

4年弱 前 | 0 件の回答 | 0

0

回答

質問


Matlab Simulink RepMat Execution Time
Dear All, I need a significant help. I have a Simulink model that has a subsystem that takes a matris [3x1] and makes it [3x...

4年弱 前 | 1 件の回答 | 0

1

回答

質問


SIMULINK PROFILER - NUMBER OF CALL
Hello everyone, I am trying to use Profiler function for SIL of one of the models that I have. I was checking number of call ...

約4年 前 | 0 件の回答 | 0

0

回答

質問


Design verifier Unsupported data pointer
Dear All, We are trying to use Simulink Design Verifier in one of our model to detect PIL problem(run time failure). But we g...

約4年 前 | 1 件の回答 | 0

1

回答

質問


PIL Communication Timeout for MPC57xx
Dear All, I am trying to use external mode for C2000 and PIL for MPC57xx. for C2000 even sample project model gives commun...

4年以上 前 | 0 件の回答 | 0

0

回答

質問


SIMULINK WHILE LOOP with Estimator
Dear All, I am trying to build a while loop that tries to estimate future values. Block diagram is as below. Main Code ...

4年以上 前 | 0 件の回答 | 0

0

回答

質問


C28x Memory Operations
Dear All, I am trying to add memory operations one of my complex model. But before directly implementing to complex one , I j...

4年以上 前 | 0 件の回答 | 0

0

回答

質問


C2000 CAN RX
Dear All, I am using Simulink to build a model to receive CAN messages. You can see diagram below. I am getting "error: express...

4年以上 前 | 1 件の回答 | 0

1

回答

質問


C2000 timer interrupt for 1 second
Dear All, I want to set 1 second timer in C2000 and output an analog signal. How can I do that? Can you help me? I have also ...

4年以上 前 | 0 件の回答 | 0

0

回答

質問


C2000 SCI BYTES IN ONE FRAME
Dear All, I am trying to use C2000 SCI function. I need to send more than 1 BYTE in a frame to communicate with BQ76PL455EVM....

5年弱 前 | 0 件の回答 | 0

0

回答

質問


F28379D READING VALUES FROM GPIO INPUT AND SCI RCV
Hello, I want to see whether a digital input is HIGH or LOW but scope and display always show 0 despite of changing voltage l...

5年弱 前 | 0 件の回答 | 0

0

回答

質問


Data Store Memory to Global Workspace
Hello, I am using a function that reads some values from a data storage memeory and writes back to data storage memory. What ...

5年弱 前 | 1 件の回答 | 0

1

回答

質問


28379D GPIO INPUT
Hi, I want to use GPIO input and want to see incoming signal on my computer but incoming signal always seem as 0 Zero. How ca...

5年弱 前 | 1 件の回答 | 0

1

回答

回答済み
C2000 F28379d SCIB
Hello Venkatesh, To be clear, you mean that you have tried and used succesfully SCI B on my model, am I right? Thanks.

5年弱 前 | 0

質問


C2000 SCI B and SCI C
Hi everyone, I am using 28379d LaunchPad and could not get any signal on SCI B and SCI C. I have attached model. Can you tell...

5年弱 前 | 0 件の回答 | 0

0

回答

回答済み
C2000 F28379d SCIB
Is there anyone that can help me on this issue ?

5年弱 前 | 0

回答済み
Error in Code build for C2000 Piccolo F28027
I dont know the source of the problem. But I have learned that sometimes you need to change clock frequency on these boards. Kee...

5年弱 前 | 0

質問


C2000 F28379d SCIB
Hello, I need to use SCIB port of the F28379d on MATLAB Simulink. I assign some pins for SCIB communication and SCIC communic...

5年弱 前 | 3 件の回答 | 0

3

回答

質問


SIMSCAPE INPUT FOR SOURCE CODE
Hello eveyone, I want to use a generate a temperature dependent voltage source in simscape by using dc voltage source. Temper...

5年弱 前 | 1 件の回答 | 0

1

回答