photo

Jason R


2014 年からアクティブ

Followers: 0   Following: 0

メッセージ

統計

All
  • Knowledgeable Level 2
  • First Answer
  • Solver

バッジを表示

Feeds

表示方法

解決済み


Use a timetable to analyze a train timetable (Part 5)
You are analyzing a train timetable (you have some time to kill since you just missed your train!) How many trains depart each d...

8年弱 前

解決済み


Use a timetable to analyze a train timetable (Part 4)
You are analyzing a train timetable (you have some time to kill since you just missed your train!) What is the average daily tri...

8年弱 前

解決済み


Use a timetable to analyze a train timetable (Part 3)
Oh no, you missed your train to Boston (again?)! How many times can you miss that train today? (In other words, how many Boston ...

8年弱 前

解決済み


Use a timetable to analyze a train timetable (Part 2)
Oh no, you missed your train to Boston! Find the departure time of the next available train by analyzing the train timetable. Yo...

8年弱 前

解決済み


Use a timetable to analyze a train timetable (Part 1)
Oh no, you missed your train to Boston! Find the departure time of the next available train by analyzing the train timetable. Th...

8年弱 前

解決済み


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

約9年 前

解決済み


Determine if input is odd
Given the input n, return true if n is odd or false if n is even.

約9年 前

解決済み


Add damping to a mass spring system
Model an ideal mass-spring-damper system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/im...

約9年 前

解決済み


Model a mass spring system
Model an ideal mass-spring system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/images/se...

約9年 前

解決済み


Model a falling body
An object is falling freely from a height of 22 meters under the force of gravity. <<http://blogs.mathworks.com/images/seth/c...

約9年 前

解決済み


Make a half wave rectifier
Produce a signal that outputs the given sine wave source when it is greater than zero and outputs zero when it is less than zero...

約9年 前

解決済み


Make a full wave rectifier
Produce a full wave rectifier waveform for the given sine wave source. For a sine wave input, the output of the full wave rec...

約9年 前

解決済み


Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

約9年 前

解決済み


Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

約9年 前

解決済み


Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

約9年 前

解決済み


Produce a Fibonacci sequence
Construct a diagram that generates the Fibonacci sequence: 1, 1, 2, 3, 5, 8, 13, 21, 34.....up to 377 The Fibonacci sequ...

約9年 前

解決済み


Model a simple pendulum
Model a simple pendulum of length 200cm with bob of mass 100g and plot the position in degrees. The pendulum starts at 30 degree...

約9年 前

解決済み


Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

約9年 前

解決済み


Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

9年以上 前

解決済み


Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

9年以上 前

解決済み


Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

9年以上 前

解決済み


Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

9年以上 前

回答済み
How can I plot a root locus for an open loop system?
To find the root locus of G=1/(10s+5), use the following code: s=tf('s'); G=tf(1/(10*s+5)); rlocus(G) This should be eno...

10年弱 前 | 0

| 採用済み

回答済み
please I wrote this code to solve an equation of linear systems using LU factorization but it keeps giving me zeros as the value of x. please can someone help? thanks in advance
It seems that you initialize y as a vector of zeros (y = zeros (n,1);) and then use y to solve for b(n) and b(j) without updatin...

10年以上 前 | 0

解決済み


Add two numbers
Given a and b, return the sum a+b in c.

10年以上 前

解決済み


Find the sum of all the numbers of the input vector
Find the sum of all the numbers of the input vector x. Examples: Input x = [1 2 3 5] Output y is 11 Input x ...

10年以上 前

解決済み


Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...

10年以上 前

回答済み
Can you create a plot with contourf without the contour lines?
Use the shading flat command. Example use: Z = peaks(20); contourf(Z,10); shading flat

11年弱 前 | 0

回答済み
please please ...... i need help in this programme is there an error
What is the problem? I was able to run your code when I uncommented the variables k, v, etc. Remember that anything after a % wi...

11年弱 前 | 0

| 採用済み

回答済み
how to silence display of variables?
Use ; to suppress output. So, Y(i)=0*X(i)+0; instead of Y(i)=0*X(i)+0,

11年弱 前 | 1

| 採用済み

さらに読み込む