Feeds
回答済み
int16 to uint8 array conversion for Serial Transmit
Ok a little bit more resarch has turned out specifying data size in the model explorer works: :) <<https://i.imgur.com/PZffoq...
int16 to uint8 array conversion for Serial Transmit
Ok a little bit more resarch has turned out specifying data size in the model explorer works: :) <<https://i.imgur.com/PZffoq...
7年以上 前 | 0
回答済み
int16 to uint8 array conversion for Serial Transmit
Your answer works fine in Matlab however in simulink i get port dimension errors. This is probably due to the fact that i could ...
int16 to uint8 array conversion for Serial Transmit
Your answer works fine in Matlab however in simulink i get port dimension errors. This is probably due to the fact that i could ...
7年以上 前 | 0
質問
int16 to uint8 array conversion for Serial Transmit
Hello there, I would like to take a int16 and split it into a uint8 array to transmit via serial connection (arduino). Then ...
7年以上 前 | 3 件の回答 | 0
3
回答回答済み
See Generated code from Realtime workshop for Arduino
Hi Aj, thanks for your reply. That is exactly what i tried but then when i try to run the model on the hardware the follow...
See Generated code from Realtime workshop for Arduino
Hi Aj, thanks for your reply. That is exactly what i tried but then when i try to run the model on the hardware the follow...
10年弱 前 | 0
質問
See Generated code from Realtime workshop for Arduino
Rather simple question: How can i see the generated code when i use the realtimeworkshop with the Arduino Target? deployme...
10年弱 前 | 2 件の回答 | 0
2
回答回答済み
arduino target with interrupt and i2c comunication
stuck on the same problem...cmon matlab!
arduino target with interrupt and i2c comunication
stuck on the same problem...cmon matlab!
約10年 前 | 0
回答済み
arduino target with interrupt and i2c comunication
I am stuck at the same problem! i have tried using the S function builder and was able to successfully send data over I2C to ano...
arduino target with interrupt and i2c comunication
I am stuck at the same problem! i have tried using the S function builder and was able to successfully send data over I2C to ano...
10年以上 前 | 0
質問
Simulink Support Package for Arduino Hardware/Ethernet Shield
Hello, I was wondering if somebody could point me into the right direction of how i can i get the TCP/UDP send/receive blocks...
10年以上 前 | 1 件の回答 | 0
1
回答回答済み
Get ERROR when trying to upload 'Custom Simulink Block aka: S-Function Builder' to Arduino UNO
here is my very similar error: The build failed with the following message: "C:/MATLAB/Targets/R2012b/arduino-1.0/hardware/to...
Get ERROR when trying to upload 'Custom Simulink Block aka: S-Function Builder' to Arduino UNO
here is my very similar error: The build failed with the following message: "C:/MATLAB/Targets/R2012b/arduino-1.0/hardware/to...
11年以上 前 | 0
質問
How to write Driver Blocks for Arduino on the new 2012b Version?
Following the guide "Writing a Simulink Device Driver block: a step by step guide" by Campa I have not been able to successfully...
11年以上 前 | 0 件の回答 | 0
0
回答回答済み
lcd display with matlab simulink
hey klob... i am currently doing the exact same thing. i have had partial success!... google this: Writing a Simulink Device...
lcd display with matlab simulink
hey klob... i am currently doing the exact same thing. i have had partial success!... google this: Writing a Simulink Device...
11年以上 前 | 0