photo

Sivapriya Srinivasan

MathWorks

Last seen: 2ヶ月 前 |  2023 年からアクティブ

Followers: 1   Following: 0

I am an intern at MathWorks. My major responsibilities are Signal Processing, Image Processing, and Embedded Systems at MathWorks. DISCLAIMER: Any advice or opinions here are my own, and in no way reflect that of MathWorks.

統計

  • 3 Month Streak
  • Knowledgeable Level 2
  • First Answer

バッジを表示

Feeds

表示方法

回答済み
Labjack U3-HV with matlab for LED blinking continously
Hello, I understand that to connect to a LabJack U3-HV device and perform an analog input operation, you can use the following ...

約1年 前 | 0

回答済み
Industrial communication toolbox (R2022a): function code for Modbus multiple holding registers write
Hello, I understand that you want to force the MATLAB Modbus write function to generate a function-code-16 write, you can use t...

約1年 前 | 0

| 採用済み

回答済み
Programmable power supply not able to send value through COM
Hello, I understand to send integer values to your instrument using serial port object in matlab, want to convert integer to s...

約1年 前 | 0

回答済み
serialport upload data using Ymodem protocol
Hello, To communicate using the Y-modem protocol in MATLAB, you can use the serialport object and the write and read functions...

約1年 前 | 0

回答済み
Serial Port Connects but no transmission is possible (Time out error)
Hello , I understand that you are experiencing a timeout issue when communicating with Lab instrument through MATLAB, even tho...

約1年 前 | 0

回答済み
error using serialport(line116)
    Hello Nilay, I understand that you are encountering an issue when trying to connect MATLAB with Arduino using the fopen ...

約1年 前 | 0

回答済み
GUI for realtime data capture of mutiple channels from Texas Instruments board
Hello, To start with capturing electromyography (EMG) data using the Texas Instruments ADS131E08 on an MMB0 board, you can fol...

約1年 前 | 0

回答済み
How do I configure data in simulink for serial transmission over dSPACE RTI
Hello Brenton, To transmit 12 8-bit values from dSPACE RTI(real time interface) to a LabVIEW controller using a UART serial po...

約1年 前 | 0

回答済み
TI F28069M LaunchPad - XINT
Hello, I understand that you want to set a specific exit condiion for your hardware interupt ,you can follow the following step...

約1年 前 | 0

回答済み
I am unable to connect tektronix AFG3101C(functon genertor) with matlab.
Hi Azim, I understand you are experiencing issues connecting your instrument through instrument control in MATLAB,even though i...

約1年 前 | 0

回答済み
TI F28069M Launchpad with BOOSTXL-DRV8305 inverter: which examples are valid ?
Hi Ronny, I understand that you want to run the "mcb_param_est_host_read" for any suitable hardware To make the "mcb_param_est...

約1年 前 | 0

回答済み
OPC UA fails to connect in Simulink but connects in Matlab
Hi Shahab, I understand that you are receiving an error indicating that the Simulink OPC Config block is unable to retrive the...

約1年 前 | 0

回答済み
DAQ multiple rates with digital output
Hello , I understand that you are experincing synchronzation issues with the digital output channels while generating pulses us...

約1年 前 | 0

回答済み
High and Variable Latency in MQTT Communication Using the Industrial Communication Toolbox
Hello , Here are a few potential causes and suggestions to address the issue: MATLAB processing time: MATLAB might have addi...

約1年 前 | 0

回答済み
C2000 can EPWMxBLANK be routed out to a GPIO pin?
Hello Richard, Yes, you can route the ePWM blanking signal to a GPIO pin for monitoring it on a scope. On the F28388D microcon...

約1年 前 | 0

回答済み
Couldn't connect to mpu6050 sensor
Hello The error message you received indicates that the function 'mpu6050' is not recognized by MATLAB. This error typically oc...

約1年 前 | 0

回答済み
i want to find out cheybsev type 1 filter average of graph FOR ORDER UPTO 50 . but one error is coming
Hello The error message you're seeing indicates that the index fs in the line if smr(1,fs)~=1 exceeds the array bounds. This me...

約1年 前 | 0

回答済み
Is it wrong with my equation for energy? Cause my manual calculation not same with this.
Hello, The equation you provided for calculating energy seems to be correct. However, it's important to note that the integrati...

約1年 前 | 0

回答済み
Code generation for PIC32 fails while using ADC due to Error: bitfield ADCEOSIF not found. bitFieldsSFR_Index = 14.
Hello, As the error suggests that there might be an issue with the code generation process for the ADC module on the PIC32MK05...

約1年 前 | 0

| 採用済み

回答済み
5G Simulink error
Hello, If the Median Filter block in Simulink is not working as expected for removing impulse noise in your 5G waveform, you c...

約1年 前 | 0

回答済み
Mambo Parrot drone firmware is not updating using Simulink Support Package for Parrot Minidrones interface
1. Ensure that the USB cable you are using to connect the drone to your computer is functioning properly. Try using a different ...

約1年 前 | 0

回答済み
Silent Activation on Linux Ubuntu with no GUI at the bash shell
Ensure that the path to the license file is accurate and accessible by the user running the command. You may need to adjust the ...

約1年 前 | 0

回答済み
How to read data from arduino and analyze in real time
1.Create two separate threads—one for data reading and one for data analysis. Each thread will execute its respective function i...

約1年 前 | 0

回答済み
Trying to install a network license on my laptop
Hey Gavin, 1.Review the license documentation :Administer Network Licenses - MATLAB & Simulink (mathworks.com) 2.Check if ther...

約1年 前 | 0

回答済み
About phased array design
Hello, To create a transmit antenna array with different lambda values and shifted in the up direction, you can follow these st...

1年以上 前 | 1

回答済み
ESP 300 controller program not working
Hey Prashanth, Here are some troubleshooting steps you can take to try and resolve the issue: 1.Check the connection: Make s...

1年以上 前 | 0

回答済み
MRI segmentation for different platforms
Hello, The NIfTI file format is a popular format for storing neuroimaging data, such as MRI, fMRI, and PET scans, in a way tha...

1年以上 前 | 0

回答済み
iLLD drivers for Embedded Coder Support Package for Infineon AURIX TC4x Microcontrollers not available
Hi Pedro Martinez, If the installation link provided during the setup of the "Embedded Coder Support Package for Infineon AURIX...

1年以上 前 | 0

回答済み
How do i compare more than two simscape simulations runs?
Hello, You can try to create two or more separate subplots in the same figure window using the subplot MATLAB function You c...

1年以上 前 | 0

回答済み
DAC (digital to analogue conversion) monitoring issue
Hello, Here are some ways to try 1.The oscillator frequency must match the Launchpad’s external oscillator frequency. While...

1年以上 前 | 0

さらに読み込む