統計
All
ランク
of 170,890
コントリビューション
0 問題
0 解答
スコア
0
バッジ数
0
コントリビューション
0 投稿
コントリビューション
0 パブリック チャネル
平均評価
コントリビューション
0 ハイライト
平均いいねの数
Feeds
回答済み
PMSM motor cannot start up when using launchpad F28379D + FOC in simulink
Run the example in open-loop control mode to validate the hardware setup and motor. The example has an open loop start-up. Modif...
PMSM motor cannot start up when using launchpad F28379D + FOC in simulink
Run the example in open-loop control mode to validate the hardware setup and motor. The example has an open loop start-up. Modif...
約1ヶ月 前 | 0
回答済み
示例《Sensorless Field-Oriented Control of PMSM Using DC Shunt Current Sensing》中，仿真和代码生成的相移方向是相反的，应如何理解？
Hello, thank you for the question. Your observation is correct. Hardware configuration is for rising edge but simulation plant l...
示例《Sensorless Field-Oriented Control of PMSM Using DC Shunt Current Sensing》中，仿真和代码生成的相移方向是相反的，应如何理解？
Hello, thank you for the question. Your observation is correct. Hardware configuration is for rising edge but simulation plant l...
約2ヶ月 前 | 0
| 採用済み
送信済み
Motor Control Using NXP™ Development Kits
Field-Oriented Control of Permanent Magnet Synchronous Motor Using NXP™ Development kits
3ヶ月 前 | ダウンロード 13 件 |
送信済み
Demos for Motor Control Deployment on Renesas Controllers
PMSM control examples using the Renesas motor control development kits.
7ヶ月 前 | ダウンロード 9 件 |
回答済み
Sensorless Control with High Frequency Signal Injection at Low Speed
Please refer to the following document page: Initial Position Estimation and Field-Weakening Control of IPMSM Using Pulsating Hi...
Sensorless Control with High Frequency Signal Injection at Low Speed
Please refer to the following document page: Initial Position Estimation and Field-Weakening Control of IPMSM Using Pulsating Hi...
9ヶ月 前 | 0
回答済み
How to generate first value for Kp, Ki of PID in current controller
Please refer to the following document page: Estimate Control Gains and Use Utility Functions.
How to generate first value for Kp, Ki of PID in current controller
Please refer to the following document page: Estimate Control Gains and Use Utility Functions.
9ヶ月 前 | 1
回答済み
In the BLDC motor block, a non-standard d'q' Transformation is used. Does this affect the values of L_d and L_q?
Thank you for providing your valuable feedback. The factor of π is a typographical error in the documentation and will be correc...
In the BLDC motor block, a non-standard d'q' Transformation is used. Does this affect the values of L_d and L_q?
Thank you for providing your valuable feedback. The factor of π is a typographical error in the documentation and will be correc...
9ヶ月 前 | 0
送信済み
Motor Swap of PMSM Using Microchip MCS MCLV-48V-300W
Run any three-phase PMSM using Microchip MCS MCLV-48V-300W Development Board and dsPIC33AK128MC106 MC DIM
9ヶ月 前 | ダウンロード 3 件 |
送信済み
Demos for Motor Control Deployment on Microchip Controllers
PMSM control examples using the Microchip motor control development kit.
2年弱 前 | ダウンロード 10 件 |
回答済み
TI F28379D Launchpad Serial Communication Failure
In mcb_param_est_host_read, update the COM port in 3 blocks, Host Serial Setup, Host Serial Receive, Host Serial Transmit. You ...
TI F28379D Launchpad Serial Communication Failure
In mcb_param_est_host_read, update the COM port in 3 blocks, Host Serial Setup, Host Serial Receive, Host Serial Transmit. You ...
2年以上 前 | 0
| 採用済み
回答済み
I want to make 'Deploying Motor Control Algorithms on Microchip dsPIC, PIC32, and SAM Controllers'. But MPLAB version is different. Could you give me the 3.50 version?
Hi, Please post a query at MPLAB Device Block page to check if it supports 3.50 version.
I want to make 'Deploying Motor Control Algorithms on Microchip dsPIC, PIC32, and SAM Controllers'. But MPLAB version is different. Could you give me the 3.50 version?
Hi, Please post a query at MPLAB Device Block page to check if it supports 3.50 version.
2年以上 前 | 0
