![photo](/responsive_image/150/150/0/0/0/cache/matlabcentral/profiles/10676227_1536999793735_DEF.jpg)
Ardeal Liang
2018 年からアクティブ
Followers: 0 Following: 0
Feeds
質問
Recevied signal from ARM is not correct
Hi, I have zedboard and AD9364. I am trying to reproduce the Matlab example in ARM in C code: Receive Tone Signal Using Ana...
6年弱 前 | 0 件の回答 | 0
0
回答質問
Set the source of transmitter to be DDS on zedboard and AD3964
Hi, I have the boards: AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard I am going to try the experiment of Matlab in C ...
6年弱 前 | 0 件の回答 | 0
0
回答質問
The specified superclass 'comm.internal.SDRTxZynqFMC234Base' contains a parse error, cannot be found on MATLAB's search path, or is shadowed by another file with the same name
Hi Paul, I am trying to package the example code as an individual app via Matlab menu: APPS-->APPLICATION DEPLOYMENT --> A...
6年弱 前 | 0 件の回答 | 0
0
回答質問
How to control GPIO of ARM on Zedboard
Hi Paul, I would like to control the GPIO of ARM on my Zedboard. I would like to set one/some GPIO to be 1 or 0. Which ...
6年弱 前 | 1 件の回答 | 0
1
回答回答済み
Chang center frequency quickly
Hi Paul, Thanks for your answer! Here are the steps(pseudo-code) of the exeriment I wang to do: for rf_scan = 1:10 ...
Chang center frequency quickly
Hi Paul, Thanks for your answer! Here are the steps(pseudo-code) of the exeriment I wang to do: for rf_scan = 1:10 ...
6年弱 前 | 0
回答済み
Chang center frequency quickly
Hi Paul, At present, the example runs on Matlab, and send commands to ARM to talk to AD9364 by RJ45 interface. So, the exa...
Chang center frequency quickly
Hi Paul, At present, the example runs on Matlab, and send commands to ARM to talk to AD9364 by RJ45 interface. So, the exa...
6年弱 前 | 0
| 採用済み
質問
Chang center frequency quickly
Hi Paul, I would like to change center frequency quickly. If I change it and then restart the object in Matlab, it runs too ...
6年弱 前 | 3 件の回答 | 0
3
回答質問
The received signal from sdrrx keeps unchanged even if I connect or disconnect the loopback cable to trainsmitter port TxA and receiver port RxA
Hi, I am trying to reproduce this example: Receive Tone Signal Using Analog Devices AD9361/AD9364from: https://ww2.mathwor...
6年弱 前 | 1 件の回答 | 0
1
回答回答済み
Question about how to run TX and RX calibration example model on zedboard with zynq
Hi Paul, Many thanks for your answer! according to your answer, I should not run tx and rx on one board. However, I cannot u...
Question about how to run TX and RX calibration example model on zedboard with zynq
Hi Paul, Many thanks for your answer! according to your answer, I should not run tx and rx on one board. However, I cannot u...
6年弱 前 | 0
質問
Run transmitter and receiver model in 1 model or 2 separate model in parallel
I have only 1 set of the hardware boards(AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard). so I will run both transmitter and re...
6年弱 前 | 1 件の回答 | 0
1
回答回答済み
Question about how to run TX and RX calibration example model on zedboard with zynq
In the Matlab help link: https://ww2.mathworks.cn/help/supportpkg/xilinxzynqbasedradio/examples/frequency-offset-calibratio...
Question about how to run TX and RX calibration example model on zedboard with zynq
In the Matlab help link: https://ww2.mathworks.cn/help/supportpkg/xilinxzynqbasedradio/examples/frequency-offset-calibratio...
6年弱 前 | 0
質問
Question about how to run TX and RX calibration example model on zedboard with zynq
I am doing an experiment: I combined the following two examples: Transmitter example: https://ww2.mathworks.cn/help/support...
6年弱 前 | 3 件の回答 | 0