Can't draw two plots with animated lines?

I was trying to design a program to receive a data and plot the real time information. This is my first time recording real time information. I needed two plots one with raw data and another with filtered data. But I can't even get the two graph to show the same information. Please help!!!

Error Message: Invalid or deleted object.

Error in trial2 (line 28)

ax.XLim = datenum([t-seconds(15) t]);

My code:

%% Clear all previous information from arduino board:
clc;
clear;
close all;

%% Use the arduino command to connect to an Arduino device.

a = arduino;

writeDigitalPin(a, 'D10', 1);

%% Receiving signal from Arduino and plotting the live data:
figure
h1 = animatedline;
ax = gca;
ax.YGrid = 'on';
ax.YLim = [-5 5];

stop = false;
startTime = datetime('now');
while ~stop
        
    v = readVoltage(a,'A0');
    v2 = readVoltage(a,'A0')-1;
    
    t =  datetime('now') - startTime;
    addpoints(h1,datenum(t),v)
    ax.XLim = datenum([t-seconds(15) t]);
    
    
    subplot(2,1,1)
    xlabel('Elapsed time (sec)')
    title('Raw Signal')    
    drawnow
       
    subplot(2,1,2)
    xlabel('Elapsed time (sec)')
    title('Filtered Signal')
    drawnow
    datetick('x','keeplimits')
    
    
    stop = readDigitalPin(a,'D3');
end

[Geoff Hayes]

up_pro - on which iteration of the loop did this error occur? Did you manually close the figure? Which may explain the invalid axes object? (I'm guessing that it is the axes that has become invalid...)

[up_pro]

No, I didn't. The plot didn't display anything. and then the error msg appeared. It works perfectly fine when I only have one plot but with two, the error msg appears. My code with one plot is:

clc;

clear;

close all;

%% Use the arduino command to connect to an Arduino device.

a = arduino;

writeDigitalPin(a, 'D10', 1);

%% Receiving signal from Arduino and plotting the live data:

figure

h = animatedline;

ax = gca;

ax.YGrid = 'on';

ax.YLim = [-5 5];

stop = false;

startTime = datetime('now');

while ~stop

% Read current voltage value

v = readVoltage(a,'A0');

% Get current time

t = datetime('now') - startTime;

% Add points to animation

addpoints(h,datenum(t),v)

% Update axes

ax.XLim = datenum([t-seconds(5) t]);

datetick('x','keeplimits')

xlabel('Elapsed time (sec)')

ylabel('Voltage (micro-V)')

title('Raw Signal')

drawnow

% Check stop condition

stop = readDigitalPin(a,'D3');

end

Answer 1

[up_pro]

Solved the problem:

figure

subplot(2,1,1)

h1 = animatedline;

ax1 = gca;

ax1.YGrid = 'on';

ax1.YLim = [-5 0];

subplot (2,1,2)

h2 = animatedline;

ax2 = gca;

ax2.YGrid = 'on';

ax2.YLim = [0 5];

stop = false;

startTime = datetime('now');

while ~stop

% Read current voltage value

v = -readVoltage(a,'A0');

v_rms = rms(v);

% Get current time

t = datetime('now') - startTime;

% Add points to animation

addpoints(h1,datenum(t),v)

addpoints(h2,datenum(t),v_rms)

% Update axes

% Update axes

ax1.XLim = datenum([t-seconds(15) t]);

ax2.XLim = datenum([t-seconds(15) t]);

datetick('x','keeplimits')

xlabel('Elapsed time (sec)')

ylabel(ax1,'Voltage (micro-V)')

ylabel(ax2,'Voltage (micro-V)')

title(ax1,'Raw Signal')

title(ax2,'rms signal')

drawnow

% Check stop condition

stop = readDigitalPin(a,'D3');

end