Create table from array in a loop
15 ビュー (過去 30 日間)
古いコメントを表示
Hi all,
I am working on code that is able to read two columns of data (Diameter and height ) belonging to various Excel spreadsheets pertaining to collected data so that these can be grouped in 5mm groups according to a Diameter values.
My first approach was to produce a specific code for each project as described below, so that in the end I could work from the data populated as per table Vtotal:
rawTable = readtable('20220209_Diameter.xlsx','Sheet','ExportResult');
x = rawTable.x; %: Column x
y = rawTable.y; %: Column y
V835 = rawTable((rawTable.x > 830) & (rawTable.x <= 835),:);
V835M = table2array(V835(:,2:3));
V835M(:,3)=835;
V835N = array2table(V835M,'VariableNames',{'x','y','z'});
V840 = rawTable((rawTable.x > 835) & (rawTable.x <= 840),:);
V840M = table2array(V840(:,2:3));
V840M(:,3)=840;
V840N = array2table(V840M,'VariableNames',{'x','y','z'});
Vtotal = [V835N; V840N; V845N; V850N; V855N; V860N; V865N; V870N; V875N; V880N];
Xtotal = Vtotal.z;
Ytotal = Vtotal.y;
boxplot(Ytotal, Xtotal)
I would now be looking to create a standard code that is able to read any set of data belonging to the different spreadsheets mentioned above, so have produced the following code.
range=5;
rawTable = readtable('20220209_Diameter.xlsx','Sheet','ExportResult');
x = rawTable.x; %: Column x
y = rawTable.y; %: Column y
Diam_min=790; % Add minimum diameter
Diam_max=860; % Add maximum diameter
n_div=(Diam_max-Diam_min)/range;
Diam=x;
Sh=y;
for j=1:n_div
V = rawTable((rawTable.x > (Diam_min+(j-1)*range)) & (rawTable.x <= (Diam_min+j*range)),:);
VM = table2array(V(:,2:3));
VM(:,3)=Diam_min+j*range-range/2; % Valor en el que centramos el boxplot en "X"
VN = array2table(VM,'VariableNames',{'x','y','z'});
end
What I require, is the above Vtotal table to be populated after each iteration so that I get the same sort of data as above and bearing in mind that the data amount and grouping will vary between spreadsheets.
0 件のコメント
採用された回答
Stephen23
2022 年 3 月 8 日
編集済み: Stephen23
2022 年 3 月 8 日
"to collected data so that these can be grouped in 5mm groups according to a Diameter values."
The MATLAB approach would be to use some simple, very efficient mathematics. For example:
X = 800+23*rand(9,1);
Y = 32*rand(9,1);
T = table(X,Y) % your input data
T.G = 5*ceil(T.X/5)
boxplot(T.Y,T.G)
Vtotal = sortrows(T,'G')
その他の回答 (1 件)
Peter Perkins
2022 年 3 月 9 日
In addition to what Stephen has said, this code (which as Stephen points out was unncessary)
V835 = rawTable((rawTable.x > 830) & (rawTable.x <= 835),:);
V835M = table2array(V835(:,2:3));
V835M(:,3)=835;
V835N = array2table(V835M,'VariableNames',{'x','y','z'});
could have been much simpler. I would think something like this:
V835N = rawTable((rawTable.x > 830) & (rawTable.x <= 835),["x" "y"]);
V835.z(:) = 835;
People tend to overuse table2array/array2table. Often just a dot works.
0 件のコメント
参考
カテゴリ
Help Center および File Exchange で Spreadsheets についてさらに検索
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!