Perform cross co-relation to find best fit

2 ビュー (過去 30 日間)
Sajid Afaque
Sajid Afaque 2021 年 12 月 10 日
コメント済み: Sajid Afaque 2022 年 3 月 14 日
Hello Community,
I have two signals s_acti.mat and phs1.mat.
how do i find the time interval of s_acti that best fits with phs1.
i intend to perform cross corelation and find the suitable time frame in s_acti that best fits with phs1.

回答 (1 件)

Mathieu NOE
Mathieu NOE 2021 年 12 月 13 日
hello
the two signals have a slightly (but constant) slopes , so the best estimation of time delta is measured at half the amplitude
>> dt = - t0_neg1 + t0_neg2
dt = 1.1076e-08
code :
clc
clearvars
load('s_acti.mat');
time1 = s_acti(:,1);
data1 = s_acti(:,2);
load('phs1.mat');
time2 = phs1(:,1);
data2 = phs1(:,2);
%% my code below
threshold = min(data1)/2; % your value here
[t0_pos1,s0_pos1,t0_neg1,s0_neg1]= crossing_V7(data1,time1,threshold,'linear'); % positive (pos) and negative (neg) slope crossing points
% ind => time index (samples)
% t0 => corresponding time (x) values
% s0 => corresponding function (y) values , obviously they must be equal to "threshold"
[t0_pos2,s0_pos2,t0_neg2,s0_neg2]= crossing_V7(data2,time2,threshold,'linear'); % positive (pos) and negative (neg) slope crossing points
figure(4)
plot(time1,data1,time2,data2,time1,threshold*ones(size(time1)),'k--',t0_neg1,s0_neg1,'dr',t0_neg2,s0_neg2,'dg','linewidth',2,'markersize',12);grid on
legend('signal 1','signal 2','threshold','negative slope crossing points signal 1','negative slope crossing points signal 2');
dt = - t0_neg1 + t0_neg2
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
function [t0_pos,s0_pos,t0_neg,s0_neg] = crossing_V7(S,t,level,imeth)
% [ind,t0,s0,t0close,s0close] = crossing_V6(S,t,level,imeth,slope_sign) % older format
% CROSSING find the crossings of a given level of a signal
% ind = CROSSING(S) returns an index vector ind, the signal
% S crosses zero at ind or at between ind and ind+1
% [ind,t0] = CROSSING(S,t) additionally returns a time
% vector t0 of the zero crossings of the signal S. The crossing
% times are linearly interpolated between the given times t
% [ind,t0] = CROSSING(S,t,level) returns the crossings of the
% given level instead of the zero crossings
% ind = CROSSING(S,[],level) as above but without time interpolation
% [ind,t0] = CROSSING(S,t,level,par) allows additional parameters
% par = {'none'|'linear'}.
% With interpolation turned off (par = 'none') this function always
% returns the value left of the zero (the data point thats nearest
% to the zero AND smaller than the zero crossing).
%
% check the number of input arguments
error(nargchk(1,4,nargin));
% check the time vector input for consistency
if nargin < 2 | isempty(t)
% if no time vector is given, use the index vector as time
t = 1:length(S);
elseif length(t) ~= length(S)
% if S and t are not of the same length, throw an error
error('t and S must be of identical length!');
end
% check the level input
if nargin < 3
% set standard value 0, if level is not given
level = 0;
end
% check interpolation method input
if nargin < 4
imeth = 'linear';
end
% make row vectors
t = t(:)';
S = S(:)';
% always search for zeros. So if we want the crossing of
% any other threshold value "level", we subtract it from
% the values and search for zeros.
S = S - level;
% first look for exact zeros
ind0 = find( S == 0 );
% then look for zero crossings between data points
S1 = S(1:end-1) .* S(2:end);
ind1 = find( S1 < 0 );
% bring exact zeros and "in-between" zeros together
ind = sort([ind0 ind1]);
% and pick the associated time values
t0 = t(ind);
s0 = S(ind);
if ~isempty(ind)
if strcmp(imeth,'linear')
% linear interpolation of crossing
for ii=1:length(t0)
%if abs(S(ind(ii))) >= eps(S(ind(ii))) % MATLAB V7 et +
if abs(S(ind(ii))) >= eps*abs(S(ind(ii))) % MATLAB V6 et - EPS * ABS(X)
% interpolate only when data point is not already zero
NUM = (t(ind(ii)+1) - t(ind(ii)));
DEN = (S(ind(ii)+1) - S(ind(ii)));
slope = NUM / DEN;
slope_sign(ii) = sign(slope);
t0(ii) = t0(ii) - S(ind(ii)) * slope;
s0(ii) = level;
end
end
end
% extract the positive slope crossing points
ind_pos = find(sign(slope_sign)>0);
t0_pos = t0(ind_pos);
s0_pos = s0(ind_pos);
% extract the negative slope crossing points
ind_neg = find(sign(slope_sign)<0);
t0_neg = t0(ind_neg);
s0_neg = s0(ind_neg);
else
% empty output
ind_pos = [];
t0_pos = [];
s0_pos = [];
% extract the negative slope crossing points
ind_neg = [];
t0_neg = [];
s0_neg = [];
end
end
  6 件のコメント
Mathieu NOE
Mathieu NOE 2022 年 3 月 14 日
hello Sajid
good news and happy that you could find a solution to your problem
all the best
M
Sajid Afaque
Sajid Afaque 2022 年 3 月 14 日
Thanks !!

サインインしてコメントする。

カテゴリ

Help Center および File ExchangeLogical についてさらに検索

製品


リリース

R2020b

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by