回答済み
Controlling a bidirectional AC/DC converter stable with no power transfer
The control algorithm is not correctly implemented. Right now, there is no feedback on d-axis current but there is feedback on ...

約1ヶ月前 | 0

回答済み
Using powergui FFT analysis to calculate the input power factor and the displacement power factor.
The FFT Analyzer app allows you to perform Fourier analysis of simulation data and provides access to all the simulation data th...

約1ヶ月前 | 0

回答済み
PV array with DC-DC buck boost Converter
In PV array, Advanced tab, enable Break algebraic loop in internal model. In discrete models, the parameter is visible only if t...

約1ヶ月前 | 0

回答済み
why isn't ideal IGBT and MOSFET showing instantanteous switching on and off?
This appears to be an issue with the model max step size rather than the electrical model. https://mathworks.com/help/simulink...

約1ヶ月前 | 0

回答済み
How does the electrical circuit of a Battery work?
To get more insights into this model you can check out the references from the doc page. Particularly, reference [3] that is dis...

約1ヶ月前 | 0

回答済み
Oscillation in simple PV circuit
There is no control implemented for the Boost converter as it is (no voltage feedback and no inductor current feedback). Connect...

約1ヶ月前 | 0

回答済み
Three-Phase PI Section Line VS Distributed Parameter Line ?
The PI Section model represents the transmission line with parameters lumped in a PI section. In the Distributed Parameters Line...

約1ヶ月前 | 0

回答済み
Freewheeling diode causing error in Full-Bridge Inverter model
This model appears to be stiff and poses challenges to the solver. Running the model in fixed-step global solver is not the best...

約1ヶ月前 | 0

回答済み
Battery modeling lead acid constant current charging mode
In this mode the battery is continuously charging. When the SOC reaches 100% the fully charged voltage is reached. However, as t...

約1ヶ月前 | 0

回答済み
Nonlinear solver: Linear Algebra error. Failed to solve using iteration matrix. Initial conditions solve failed to converge.
This model is structurally singular because some variables are missing from the final set of equations. Double check if the equa...

約1ヶ月前 | 0

回答済み
Ideal Switch implementation in Simulink
As per the attached circuit this is the expected behavior as a current is forced into the circuit. The voltage across the resist...

約1ヶ月前 | 0

回答済み
Why do I see huge voltage spikes at the output of a 3 phase MMC (Modular multi-level converter) in Simscape, when the number of submodules >1, but not with 1 submodule?
The model may be a bit challenging for the solver due to parameterization. In this case, one way to avoid these spikes is to swi...

約1ヶ月前 | 1

| 採用済み

回答済み
I have some issues with derivating D-Q inductance from a five-phase FEA data.
The code implementing the mathematical transform does not look right as it seems that only mutual inductances are used (Laa, Lbb...

約1ヶ月前 | 0

回答済み
Bridgeless boost PFC modeling
The shape can be affected by inappropriate parameterization such as capacitor, inductor and other elements. For an example of to...

約1ヶ月前 | 0

回答済み
Pole pair on Single Phase Asynchronous motor Cap Start-Run
When simulating a single-phase asynchronous motor, the number of pole pairs directly affects the motor's speed. The negative RPM...

約1ヶ月前 | 0

回答済み
flickering lamp with visual effects in simulink
It is possible to simulate an electrical system with flickering voltage in 1D in Simscape Electrical or even Simulink. To visual...

約1ヶ月前 | 0

回答済み
Trying to model a hoist with dc motor
There are a few issues with the model. The PI controller is not connected properly as the error is passed to P and I parameter i...

約1ヶ月前 | 0

回答済み
Error when running simple voltage converter in simulink
Changing the initial value for the capacitor voltage to a non-zero value may help the solver. Without the model is not easy to p...

約1ヶ月前 | 0

回答済み
Please someone explain me how does the following code works?
If the purpose is to edit a library block, this may not be very easy. There are .p files that are protected and will not be poss...

約1ヶ月前 | 0

回答済み
how to get Beta in power transformation ?
In continuous time, to achieve a 90-degree phase shift, you can use a Transport Delay block (or a Variable Transport Delay). The...

約1ヶ月前 | 0

回答済み
Reference frame for MATLAB-SimPowerSystems' asynchronous machine model measurement signals (e.g phiqr,phidr)
This would depend on the block mask parameter Reference frame. This parameter controls the reference frame that is used to conve...

約1ヶ月前 | 0

回答済み
armature controlled dc motor
At time 10 the load torque is increased from 0 and it settles at around 0.4. As the load stays at a nonzero value it is normal t...

約1ヶ月前 | 0

回答済み
How can i switch the DC output of fuel cell in hybrid system?
A DC contactor should do the job. DC contactors are electrically controlled switches used for switching high power circuits.

約1ヶ月前 | 0

回答済み
Linear induction motor in simscape
This error can also be a consequence of how the simulation model was built and I suspect is not the custom code the culprit. Th...

約1ヶ月前 | 0

回答済み
In MUTUAL INDUCTANCE block, what does the mutual resistance mean ?
The mutual resistance and inductance corresponds to the magnetizing resistance and inductance on the standard transformer circui...

約1ヶ月前 | 0

回答済み
Modeling of NPN silicon phototransistor
Simscape Electrical provides a variety of semiconductor devices (https://mathworks.com/help/sps/semiconductors.html). The photot...

約1ヶ月前 | 0

回答済み
Newbie starter - AC generator circuit in Simulink
Mechanical power at the machine's shaft, in W. In generator mode, this input can be a positive constant or function or the outpu...

約1ヶ月前 | 0

回答済み
Unable to simulate a fault on a Three-Phase Power Line
The block implements a short-circuit fault between phases or between a phase and ground. For example, to program a fault between...

約1ヶ月前 | 0

回答済み
Simscape Synchronous reluctance motor model issue
We don’t know the assumptions used in the custom model. I have spotted a few sign mismatches that I believe should be different ...

約1ヶ月前 | 0

回答済み
Having problem with VSI controller
There are a few fundamental issues with the model. First, a DC voltage source is used to keep the DC-link voltage constant. Ther...

約1ヶ月前 | 0