Feeds
質問
Simulink scope trace is grayed out
In simulink I have a scope with three inputs. The scope has 3 subplots. The first and third input have a mux in front, and ...
11ヶ月 前 | 0 件の回答 | 0
0
回答質問
Run an enabled and triggered subsystem only one time (single shot)
I have a Simulink enabled and triggered subsystem that I want to execute only one time. I think one way to do it is to make ...
11ヶ月 前 | 1 件の回答 | 0
1
回答質問
Simulink dashboard button matching
I'm looking for suggestions on how to approach a Simulink interface problem. In case 1 below, both dashboard buttons have con...
12ヶ月 前 | 1 件の回答 | 0
1
回答質問
A few basic Simulink/Simscape questions
In the past I've generally used Simulink simulations for short bursts of transient analysis. I was curious if it were possibl...
12ヶ月 前 | 1 件の回答 | 0
1
回答質問
Dynamic dashboard radio button options
Hello! I was curious if it was possible to make the options of a radio button change based on another radio button. This is ...
12ヶ月 前 | 2 件の回答 | 0
2
回答質問
variables with scope local to subsystem
I'm a bit confused about variable scope. I think I know what's going on but am looking for confirmation and maybe advice on th...
4年弱 前 | 1 件の回答 | 0
1
回答回答済み
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...
4年弱 前 | 0
| 採用済み
質問
Radio Button Mask for Simscape Block
I have a stock Simscape block (Cauer Element) that has two parameters - Resistance and Tau. I am trying to add a mask to modify...
4年弱 前 | 1 件の回答 | 0
1
回答質問
get_param fails with simscape block
Weird/unexpected behavior, not sure if it's a bug. I'm trying to use get_param to access a stock simscape thermal component. I...
4年弱 前 | 1 件の回答 | 0
1
回答回答済み
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...
4年弱 前 | 0
回答済み
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...
4年弱 前 | 0
質問
Simscape Block Parameter not Tunable
I wish to control a Simscape block parameter using the dashboard slider switch. I select Temperature Source, but the slider swi...
約4年 前 | 1 件の回答 | 0
1
回答質問
Simulink dashboard switch to control masked parameter
I wanted to have a slider switch control such that On position would make it 1 Ohm and off position would make it 5 ohms. The s...
約4年 前 | 1 件の回答 | 0
1
回答回答済み
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...
約4年 前 | 0
| 採用済み
回答済み
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.
約4年 前 | 2
質問
Parameter Writer block not recognizing blocks
In image below I show a sim with a slider switch that modifies the constant block on the left. This the uses a goto/from block ...
約4年 前 | 1 件の回答 | 0
1
回答回答済み
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).
約4年 前 | 0
| 採用済み
質問
Is there a way to nest transfer functions?
I wish to build up a transfer function inside a for loop such that each iteration builds up a new transfer function based on pre...
約4年 前 | 1 件の回答 | 0
1
回答質問
Basic Slider Switch question
I was curious if it was possible to make a slider switch dashboard element control more than one block simultaneously. Alterna...
約4年 前 | 3 件の回答 | 0
3
回答回答済み
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...
約4年 前 | 0
| 採用済み
質問
Simscape/Simulink persistent variable in algebraic loop
I have a simple Simscape electrical model containg a circuit that trips if a current is exceeded. I want the trip to happen a c...
約4年 前 | 2 件の回答 | 0
2
回答質問
Generate Zth transient thermal impedance curves with Simscape
Simscape has some nice thermal domain elements like Cauer thermal model elements. I was looking to generate a set of Zth curves...
約4年 前 | 1 件の回答 | 0
1
回答質問
Trying to convert Kelvin to Celsius in Simscape code
I have a simulation with some Simscape Thermal and Electrical elements. The electrical element is a modification of the stock t...
約4年 前 | 1 件の回答 | 0
1
回答質問
simscape block node arrangement
In the IGBT example here: https://www.mathworks.com/help/physmod/sps/ug/Troubleshoot-of-spice-nigbt-conversion.html the gener...
4年以上 前 | 1 件の回答 | 0
