photo

jarul


Last seen: 2年弱 前 |  2019 年からアクティブ

Followers: 0   Following: 0

統計

All
  • Thankful Level 2
  • Thankful Level 1
  • First Answer
  • First Submission
  • Explorer
  • First Review
  • Revival Level 1

バッジを表示

Feeds

表示方法

質問


SD card image creation not Successful.
I created my SD card image with the "Manual Host-Radio Hardware Setup" Now when I inserted the SD Card on my FPGA, I try to pin...

約3年 前 | 0 件の回答 | 0

0

回答

質問


Quesiton about transmitRepeat(sdrTransmit, data) and sdrTransmit.Repeat(txWavefrom)
While working on SDR, I realize that earlier Matlab used transmitRepeat and now it is changed to sdrTransmit.Repeat method. Now...

4年以上 前 | 2 件の回答 | 0

2

回答

回答済み
Zynq SDR Capture Length question!
I have another question related to the above issue. When I tried to transfer rather large size, I get the following error. G...

4年以上 前 | 0

質問


Zynq SDR Capture Length question!
While using Zynq SDR, the capture length can not exceed '16777216'. I want to capture length longer than the prescribed. I get ...

4年以上 前 | 2 件の回答 | 0

2

回答

質問


The following Matlab code runs only half of the for loop. Can anyone help me figure out the problem?
Here is the part of the matlab Code that I was working for an SDR development. In the following code, when the ind in the for l...

4年以上 前 | 1 件の回答 | 0

1

回答

回答済み
Why do I encounter "something Unexpected Occurred" after installing the "Xilinx Zynq-Based Radio, or USRP Embedded Series Radio" support packages?
Hai Colin, Thanks for your response. I was able to setup the AD9361 SDR successfully. The method mentioned in the mathworks we...

5年弱 前 | 0

質問


Error using R2019b version of the MATLAB
Just installed R2019b MATLAB. SDR with AD9361 is attached to the Host machine. The host machine's IP is set to 192.168.3.1 Th...

5年弱 前 | 6 件の回答 | 0

6

回答

回答済み
Why do I encounter "something Unexpected Occurred" after installing the "Xilinx Zynq-Based Radio, or USRP Embedded Series Radio" support packages?
I have installed just one communication toolbox as shown below: "Communications Toolbox Support Package for Xilinx Zynq-Based R...

5年弱 前 | 0

送信済み


Fibonacci calculation and measuring processing time.
Three different way of calculating fibonacci number and the quickest way.

約5年 前 | ダウンロード 1 件 |

回答済み
Error using R2019b version of the MATLAB
This morning I reinstalled R2019b ones again deleting the previous install of R2019b. I just ran the simple code to test the ca...

約5年 前 | 0

回答済み
Error using R2019b version of the MATLAB
Thanks for your response. My host machine is setup in 192.168.3.1 My radio is setup in 192.168.3.14 I can ping 192.168.3.14 a...

約5年 前 | 0

回答済み
Error using R2019b version of the MATLAB
Just to respond to your answer: Have been working on SDR AD9361 software quite sometime. One host computer is setup Linux Ubun...

約5年 前 | 0

回答済み
R2019b version and AD9361 SDR does not work correctly.
This has been reported many times, but not fixed for a month or so. I need to do further experiment. Kindly take a closer look ...

約5年 前 | 0

回答済み
Error using R2019b version of the MATLAB
To answer the above query: I am using Ubuntu 18.04 The SDR hardware is Z706 and AD9361. The libiio I am using the same since ...

約5年 前 | 0

質問


R2019b version and AD9361 SDR does not work correctly.
I have installed R2019b version of the Matlab. After installing, the matlab meant for SDR does not work correctly. Even the fo...

約5年 前 | 2 件の回答 | 0

2

回答

質問


While installing "SoC Blockset Support Package for Xilinx Devices" I have the following outcome.
Xilinx Zynq Radio Linux binaries are not installed. The third party software download error occurs. This problem has not been ...

約5年 前 | 1 件の回答 | 0

1

回答

回答済み
TWO SDR using AD9361 transmitting and receiving image problem!
I have been trying to install the Linux version of the Xilinx Zynq Radio to run SDR software for single radio. I have spend seve...

約5年 前 | 0

質問


ERROR '/home/jarul/Documents/MATLAB/SupportPackages/R2019b/toolbox/target/supportpackages/shared_linuxservices/+matlabshared/+internal/ssh2client.p'
While using MATLAB R2019b version, running SDR transmitter using AD9361 or the simulink, I get the following error. How to solv...

約5年 前 | 1 件の回答 | 0

1

回答

質問


"Error using matlabshared.internal.ssh2Client"
With R2019b version installed I can not run AD9361 SDR software. The transmit and receive functions can not be run. I get the ...

約5年 前 | 3 件の回答 | 0

3

回答

質問


MATLAB 2019b Installation of SDR for Xilinx zynq Radio problem.
I have installed MATLAB 2019b version. I want to test the code for SDR. However, I can not install the following libraries nece...

約5年 前 | 1 件の回答 | 0

1

回答

質問


Install Communication ToolBox Support Package for Xilinx zynq Based Radio on MATLAB 2019b
While trying to install "Communication ToolBox Support Package for Xilinx zynq Based Radio on Matlab 2019b" Can not install xil...

約5年 前 | 1 件の回答 | 0

1

回答

質問


TWO SDR using AD9361 transmitting and receiving image problem!
Any Mathworks group can help me with the following problems. I am running two different SDRs with different IPs and a host mach...

5年以上 前 | 1 件の回答 | 0

1

回答

回答済み
SDR using AD9361 multi-FMCOMMS I get the following error.
Thanks for your response. Yes, the Code (Transmit and Receive LTE MIMO) works fine for a single SDR fine. However, when I run on...

5年以上 前 | 0

| 採用済み

質問


SDR using AD9361 multi-FMCOMMS I get the following error.
I ran the following MATLAB code and get the following error code: Transmit and Receive LTE MIMO using Analog Devices AD9361/AD9...

5年以上 前 | 2 件の回答 | 0

2

回答