Feeds
回答済み
Suppress Simulink build summary in command window
This seems to be working. The semicolon after the evalc command is required, else you will get output. model_name = 'your_mode...
Suppress Simulink build summary in command window
This seems to be working. The semicolon after the evalc command is required, else you will get output. model_name = 'your_mode...
4年弱 前 | 1
回答済み
Delay with Show Enable Port not working as expected
Ian Winter wrote: Is there any way to get back the old block? The block is back as of 2017b (at least in the HDL Coder blo...
Delay with Show Enable Port not working as expected
Ian Winter wrote: Is there any way to get back the old block? The block is back as of 2017b (at least in the HDL Coder blo...
7年以上 前 | 2
質問
HDL Coder creates too many files in my full model, but works as expected on a subystem
I'm running into a strange problem that almost seems like a stack overflow where the stack holds all Verilog files that have bee...
9年弱 前 | 1 件の回答 | 0
1
回答質問
How to update template on multiple Simulink models (programmatically)?
As I'm learning more about HDL coder, I'm slowly iterating on a common template I want to use for all my Simulink models in a gi...
9年弱 前 | 1 件の回答 | 1
1
回答質問
Best way to do a dynamic bit slice?
I am still learning my way around HDL coder, but I'm starting to think I can't get optimal results in Verilog from the set of bu...
9年弱 前 | 1 件の回答 | 0
1
回答質問
Delay with Show Enable Port not working as expected
I just noticed that previous models I had built using the Unit Delay Enabled block were still simulating without error but the h...
9年弱 前 | 1 件の回答 | 0
1
回答質問
Are there Simulink guidelines for choosing ufix1 vs. boolean?
In the past I've tried making all my 1 bit signals in my Simulink models ufix1 or all of them boolean and neither option seemed ...
約9年 前 | 1 件の回答 | 0
1
回答質問
Can I use comment through in a dynamic Simulink mask?
I'd like to create a Simulink mask where I can comment through or uncomment a sub block of the mask based on one of the mask par...
11年以上 前 | 5 件の回答 | 4
5
回答質問
Can I expose input fixed point data type parameters to mask variables in Simulink?
I have experimented with Data Type Propagation in Simulink 2013b, and it can do some of what I want, but ideally I'd like to hav...
11年以上 前 | 0 件の回答 | 0
0
回答質問
How do I extract a single bit from signed signals in Simulink? (with no run time warnings and no HDL coder hardware cost)
Basically, I want to do bit slicing on a signed integer sfixN (having bits N-1 (sign) down to 0). E.g., I want to grab bit N-1,...
11年以上 前 | 1 件の回答 | 0
1
回答質問
Do small but non-zero coefficients in symmetric Hilbert FIR found from firpm indicate a bug?
I noticed that depending on how you generate the coefficients of a Hilbert Transform FIR, one method (firpm using 'Hilbert') giv...
12年弱 前 | 0 件の回答 | 0
0
回答質問
Can I supress a flashing title bar when refreshing plots?
I've looked at the doc page for figure properties and I don't see that this is possible, but perhaps it is. My question is prob...
14年弱 前 | 1 件の回答 | 0
