Nithin

Last seen: 2年弱前 | 2023 年からアクティブ

Followers: 0 Following: 0

統計

Feeds

回答済み
How can I work out signal to noise ratio of doppler waveform images? Any possible way?
Hi Samay, I understand that you want to find the SNR (Signal to Noise Ratio) of the given doppler waveform image. To implement...

2年弱前 | 0

回答済み
How to get the frequency,time and energy data sets of wavelet and hht?
Hi Joya, I understand that you want to extract the frequency, time and energy data from wavelet and HHT (Hilbert-Huang Transfor...

2年弱前 | 0

回答済み
Can I get a MATLAB code on how to analyze Track irregularities data with Fractal dimension via a Ruler method?
Hi Shakirudeen, I understand that you want to analyze track irregularities data with Fractal dimension using Ruler method in MA...

2年弱前 | 0

回答済み
How can i generate an Hankel matrix of the lorenz system?
Hi Antonino, I understand that you want to create the Hankel matrix of the Lorenz system, perform it over a DMD algorithm and t...

2年弱前 | 0

回答済み
How to transfer RF signal to Frequency Domain?
Hi Simo, I understand that you were able to plot the RF signal in the time domain and want to know how to plot the same in the ...

2年弱前 | 0

回答済み
Code Replacement in Embedded Coder with Embedded Matlab Functions
Hi John, I understand that you want to generate the code for “memcpy” and “memset” functions using Embedded Coder. To implemen...

2年弱前 | 0

回答済み
How I can plot average line on cdf plots?
Hi Arijet, I understand that you want to plot an average line on the CDF plots mentioned. To implement this, kindly refer to...

2年弱前 | 0

回答済み
Design FIR filter to separate signals
Hi Tu, I understand that you want to design FIR and IIR filters to separate the left signal alone. To implement this, kindly...

2年弱前 | 0

回答済み
how to determine the trace of the graph.
Hi Chandrabhan, I understand that you want to cut the cylinder with a plane (x+y+z=1) and determine the shape of the trace. T...

約2年前 | 0

回答済み
How can I use Matlab command line to [open/close/export as *.fig] signal viewer interfaces in Simulink (2021b?)
Hi Cory, I understand that you want to [open/close/export as *.fig] signal viewer interfaces in Simulink using Command Line in ...

約2年前 | 0

回答済み
How to write a code which find the value of the Newton interpolation polynomial at a given point X0?
Hi Mehmet, I understand that you want to know the process of finding the value of Newton Interpolation polynomial at a point '...

約2年前 | 0

回答済み
How could I find the power of the periodic signal on my code assuming it is either a voltage or a current waveform with a normalized load resistance of 1 Ohm and plot it.
Hi Roberto, I understand that you want to find the power of a given periodic signal with a normalized load resistance of 1 ohm ...

約2年前 | 0

回答済み
How to implement Haar wavelet from scratch
Hi Sudhir, I understand that you want to implement the "haar transform" of an audio signal without using inbuilt MATLAB functio...

約2年前 | 0

回答済み
how can i plot the amplitude spectrum centered at the zeroth frequency.
Hi Batuhan, I understand that you have a FFT of vector and want to know the process of plotting the amplitude spectrum centered...

約2年前 | 0

回答済み
How can I generate BPSK signal?
Hi Mang, To generate a Binary Phase Shift Keying (BPSK) signal for Direct Sequence Spread Spectrum (DSSS) for 5 users, kindly ...

約2年前 | 0

回答済み
How can I create a function which outputs two variables for calculating the eigenvalue * eigenvector
Hi Jonas, I understand that you want to create a function which outputs two variables on calculating the product of eigen valu...

約2年前 | 0