MPLAB Device Blocks for Simulink :dsPIC, PIC32 and SAM mcu
MPLAB Device Blocks for Simulink
MPLAB Device Blocks for Simulink target boards equipped with a dsPIC ®️, PIC32 ®️, SAMx2, SAMx5 or SAMx7.
This support package is functional from Matlab R2015a up to current version (R2023b).
Installation / Update
clean previous installation
- picclean at MATLAB prompt or
- using the add-on menu.
Installation
-
Add-on menu: earch for "MPLAB" or "MPLAB Device Block for Simulink". The live script opening at end of installation allows to check system configuration: Compiler and programming interface (MPLAB X IDE). Link to download theses tools from Microchip are provided.
-
With older matleb release, download from github and run install.p script.
Commands
-
picclean: clean-up matlab path from previous installations.
-
picsetup: from the mchp sub-folder, re-configure the matlab path if required.
-
picInfo('check'): Verify installation of compilers and tool to program chips
-
picInfo('examples'): copy example in current working folder
-
picInfo('cmd'): list command
Visit the Microchip blockset forum
Presentation
Library blocks provide easy interface to set-up DSP/MCU peripherals and interface peripheral generated code to code from embedded coder. (non-exhaustive peripheral block list: ADC, QEI, PWM, IC, OC, CN, I2C, SPI, UART, Op-Amp, Comparator, DAC...) No embedded programming knowledge is required. The blockset enable rapid prototyping on boards equipped with one Supported MCU.
Features
- Built-in scheduler including multi-tasking or single-tasking option for multi-rate models implementation.
- Advanced configuration of ADC / PWM peripheral enable PMSM motor algorithm where ADC sample time is triggered precisely within a PWM duty-cycle. The time step might also be triggered by end of ADC conversion minimizing delays.
- A custom protocol allows visualizing and recording data through the UART. The custom picgui interface allows plotting using your own matlab script incoming data in real-time. Data log enable further analysis or offline identification and allow to feed a simulation with real data.
- The custom "C function" block allows including your own code if required.
The blockset support advanced MathWorks features:
- Processor in the loop (PIL)
- External mode.
- Code replacement to benefit from DSP architecture of dsPIC
This version embed a third part tool adding blocks for UAVs projects (GPS, MAVLink, Receiver S.BUS, S.Port and F.Port blocks for dsPIC). Type picInfo to find out how to install the UxV blocks.
Requirements
- MathWorks (from R2015a to R2023b)
- Matlab
- Simulink
- Embedded Coder
- Matlab Coder
- Simulink Coder
- Microchip Ide
- MPLAB X IDE download
- Microchip Compiler:
- Microchip programmer:
- PicKit4
- ICD4
- J-32
- Snap programmer
- Real-Ice
- PicKit3
- ICD3
- Microchip kit Embedded programmer (EDBG)
- ...
Release notes
-
v3.54
- fixed: xc-dsc not found on linux
- fixed: MPLAB blocks might not show-up in the simulink library
-
v3.53
- Early support for dsPIC33CK64CDVL106
- Fixed dsPIC UART Half duplex driver issue with some chip
- Fixed one error with external mode
-
v3.52
- Added xc-dsc compiler suport for dsPIC. xc16 suport will continue
- Added unused code removal option taking place at linker stage
- Added motor control examples from INSA Lyon University (France)
- added ADC block for SAMRH707
- Refactor dsPIC scheduler code enabling further compiler optimization efficiency
- Improved DFP automatic path update
- Fixed virtual pin not showing up
- Fixed code for SPI on dsPIC with 4 byte internal SPI buffer instead of 8
- Fixed scheduler issue on dsPIC for single tasking implementation with at least one asynchronous task (user interrupt) set
- Fixed UART issue with rtiostream when using DMA implementation
- Other minor fixes
-
v3.51
- Added some options on UART driver (dsPIC)
- Added virtual pin connection (dsPIC)
- SAMC21: bugfix for UART, SPI and I2C
- Support for SAMRH707
- Fixed compatibility issue with Matlab R2023b
- Improved support for external mode with older release
- Fixed external mode UART driver using a DMA circular buffer on dsPIC
-
v3.50.35
- Added board templates for
- LVMC (dsPIC33CK256MP508)
- MCLV-48V-300W
- dsPIC33CK256MP508 DIM (internal & external Op-Amp)
- dsPIC33CK64MC105 DIM (internal & external Op-Amp)
- MCLV2
- dsPIC33CK256MP508 PIM (internal & external Op-Amp)
- dsPIC33CK64MC105 PIM (internal & external Op-Amp)
- dsPIC33EP256MC506 (external Op-Amp)
- Power Tool reference design (dsPIC33CK64MP105)
- improved linux compatibility
- added UART linux compatible baudrates
- fixed UxV third part tool with blocks for GPS, Receiver, Telemetry, Mavlink...
- bugfixes (dsPIC):
- QEI: error on first block GUI opening
- Fixed blocks behaviour when placec in a masked subsystem
- fixed DOC block to download & access MCU datasheet
- UART: GUI provide number of internal chip buffer size
- removed some warning related to fast Memcpy function
- ADC for dsPIC CK/CH: fixed missing alternative pins when two ANx shared a same pin. Provide accurate name for internal channels (IVref, Temp, Vbat, CTMU...)
- some updates on the UART Circular buffer DMA based driver
- Added board templates for
-
v3.50.33
- External mode:
- Fixed single tasking implementation with XCP
- clean dsPIC CK PWM start and stop
- improved interface when Host UART is not set prior to start external mode
- Remove MPLAB X 6.05 MDB interface used to program chip. The MDB v6.05 command line chip programming is broken. System will use either IPE v6.05, or another MDB version if available.
- Fixed dsPIC Matrix replacement memory leak when output is a vector transposed
- fixed linux issue when toolbox was installed in a path containing parenthesis like "(1)"
- improved custom linker script path issue in specifics conditions
- External mode:
-
v3.50.32
- fixed one typo within package causing issue with SAM new CAN block and dsPIC UART Circular buffer DMA driver.
-
v3.50.31
- revert using programmer in debug mode to force starts of the program (MPLAB X 6.05 should get fixed instead)
- minor improvements on toolstrip and programming functions (upated IPE)
-
v3.50.30
- Fixed program not starting until disconnecting programmer / press reset button if available
- various fixes on XCP and UART DMA driver for dsPIC
-
v3.50.29
- Added Microchip toolstirp
- Added CAN support for SAME7
- Updated QDEC quadrature function block for SAMx
- added UART Circular buffer with DMA on dsPIC
- Fixed PIC32 SPI SCK2 missing mapping
- Fixed pin mapping errors with dsPIC / PIC32
- Upated External mode XCP support on dsPIC
-
v3.50.27
- added support for dsPIC32MK EFE/EFF/EFK family
- support SPI on SAMx7
- support I2C on SAMx7
- Fixed I2C for chip with non continuous I2C references (1 2 4 5..)
- Fixed SPI potential timing issue with fast clock chips (PIC32)
- added example using custom code to write SAMx FLASH (EEPROM emulator)
- Add Timers functionality on SAMx chips
- Improved PIL support with Test Harness
- Fixed Low priority interrupt with PIC32MZ that might trig an exception
-
v3.50.26
- fixed SPI code not generated with PIC32
-
v3.50.25
- PIL: Added support for PIL Top-Model and PIL Referenced Model approach
-
v3.50.24
- Added dsPIC CK 128 & 256
- Fixed code Replacement for dsPIC not compiling in debug mode -O0 option
- PIC32 ADC High Speed SAR fixed channel of class 3 below 32 were handled as class 2 (break compilation)
-
v3.50.23
- missing file for Code Replacement for the dsPIC atan2 function
-
v3.50.22
- Improved PIL on Linux
- Fixed issue on SAMx7 when analog port is used and no othet peripheral used the same port (Letter)
- Fixed SPI & I2C peripheral block, broken with SAMx2 and SAMX5.
- Complete support for dsPIC CK MC
- dsPIC Improved Code Replacement accuracy. Fix one typo preventing compilation in rare cases
- dsPIC, Code replaced (sin, cos, atan2) works with revolution unit, not limited to radian.
-
v3.50.20
- Updated datasheet block to locate pdf from Microchip website
- Fixed dsPIC Optimized assembly code issue resulting in wrong output with XC16 v2.00 set with -Ox optimization enabled.
- Fixed Idle task call to math function not compiling
- Fixed SAMx7 analog pin configuration that might have a bias due to internal peripheral connection
- Improve compatibility with protected IP submodel
- Improved PIl support
- Experimental support for dsPIC CK MC
-
v5.50.19
- Programming interface updated. Extend number of kit programmed from matlab (use latest MPLAB X version. current release is 6.0.0)
- PIL target initialisation code improved. Fixed possible code issue with initialisation function signature mismatch
- PIL UART interface compatible with USB-COM port available on kits. Enabling host data flow control
-
v5.50.18
- SAMx7: Fixed USART generated code typo with interrupt implementation
- dsPIC CK: Fixed Change Notification User Interrupt triggered twice
- Improved UART block User Interface
- SAMx7: Add Fuse configuration ensuring Fuse get programmed
- SAMx7: Disable ICE functions on PORT B when pin is used for another purpose
- SAMx: Add compilation of intermediate model (library)
- Add PIL and External Mode example for Xplained Ultra board
- Update Installer
-
v3.50.17:
- Fixed programming not working form Linux (issue from 3.50.16)
- Update installer. Simplify installation as an add-on.
-
v3.50.16:
- C Function Call: fixed issue breaking simulink datatype class settings
- Matlab R2021b: code generator report not showing-up. Renamed compilation from .X to _X
- Improving DFP & CMSIS search script
- SAMx7 ADC: remove pull-up on analog chanels
- SAMx5 UART: add distinct priority for Tx & Rx
- SAMx5 UART: some baudrate setting were not working (no output)
- SAMx: removed register keyword wich might cause issue at compilation
- dsPIC PWM FEP: not working wheh channel 1 were not used
- dsPIC with dual core: always re-compile Main model code required.
- dsPIC: fixed code generated issue with SPI peripheral
- dsPIC: remove default fuse set for Brown Out reset
- dsPIC: fixed short double setting in MPLAB X project
- Improved MPLAB X project creation
- External mode: Add XCP protocol option (experimental)
-
v3.50.13:
- dsPIC CH (dual core): Fixed Main/Secondary Interface. MSI Fuse not configured
-
v3.50.12:
- SAMx: Fixed Link Time Optimizer incorrect syntax
- SAMx: Added CAN example for SAMx7
- SAMx: Optimized DCache update
- SAMx7: Fixed typo on UART Tx when set with DMA & single buffer
-
v3.50.11:
- Improved robustness for long or special path with Windows & Linux
- SAMx7 QDEC peripheral: added Index edge option
-
v3.50.10:
- dsPIC CH update Slave->Secondary call convention for XC16 1.70
-
v3.50.09:
- Fixed Watch dog not Disabled for some (ds)PIC chips reseting after few seconds.
- Updated PIL & External mode for dsPIC with R2020b + updated example with dsPIC33CK Curiosity board
- Fixed SAMx7 AFEC (ADC) possible issue with channel inversion (wrong block outputs)
- SAMx7 improved library inclusion in MPLAB X project
-
v3.50.08:
- Added SPI & I2C Support for SAMx2 & SAMx5
- picflash issue when multiple MPLAB X above v5.45 installed
- SAMx5 Number of UART listed might be incorrect
- SAMx5 ADC Time Step Trigger Parameters lost when model is saved
- SAMx Improved performance by removing some instruction barriere (DSP & ISB)
- dsPIC ADC HS SAR Fractional mode : typo prevent compilation.
-
v3.50.07:
- SAMx5 & SAMx7 Busy flag (for CPU load measurement ) stuck to 1 after short period of time
- SAMx chip: Add CMSIS DSP librar to MPLAB X project when using CRL (Required Mathworks Support Package for ARM Cortex-M)
- SAMx7 PWM event set to instant 0 had no effect
- SAMx7 ADC: Fixes on AFEC 1 behaviour (not working when used without AFEC0, Issue with triggering time step when used with AFEC 0)
-
v3.50.06:
- dsPIC 33FJxxGS had incorrect fuse option name (compilation break)
- Internal error might cause incorrect peripheral behaviour with blocks supporting multiple instantiation
- Fixed issue introduced with 3.50.04 that break compilation of model embedding a model reference block (sub-model)
-
v3.50.05:
- DFP & CMSIS DSP library search path not proposing newly installed package/library Linux: CMSIS DSP lib failed at compilation time
- MPLAB X project not created (R2020b, SAMx7)
-
v3.50.04:
- Added SAMx7 PWM Override block
- SAMx Peripheral Port mapping issue when a peripheral set-up several time the same pin (i.e. ADC multiple conversion of the same input pin on SAMx7)
- Fixed issue with MW environment block Sim/CodeGen for mixed model (simulation & code generation) (update)
-
v3.50.03:
- Fixed issue with MW environment block Sim/CodeGen for mixed model (simulation & code generation)
-
v3.50.02:
- Fixed CMSIS DSP Library possibly added with incorrect path for SAMx5 & SAMx2
- Enabled CMSIS DSP library link option
- Fixed SAMx7 PWM1 trigger not set on ADC depending on PWM0 and on blocks PWM0/1 execution order
-
v3.50.01:
- Fixed UART DMA Tx implementation for SAMx7
-
v3.50
- Support SAM C2x / D2x / DA1
- SAMx5 ADC: Multiple conversion per ADC, Trig ADC, Synchronize with Time Step, initialize with NVM factory calibration.
- SAMx5 QDEC: Add further options and simplify GUI.
- Linux support (except PIL & External Mode)
- dsPIC Code Replacement fixed on R2021a
- dSPIC CH/CK fixed issue on PWM HS for noncontiguous channel setup. Duty cycle block input swapped (Ch1-Ch3)
- CHANGE BEHAVIOUR !! SAMx7 PWM: Dead Time initial value were divided by 2. (1us on GUI set 0.5us on board)
- Issue if no CMSIS installed
- Improved Simulink compiler option set in MPLAB project created.
- Improve doc block ability to locate online chip datasheet
- picgui update
-
v3.49.02
- PWM HS FEP fixed several issues
- programming interface update. overall speed improvement
- Support Seeger programming hardware (J-32 / J flash Seeger driver)
- ...
-
v3.49.01:
- Fixed PIL issue with dsPIC / R2018b
-
v3.49:
- Updated External-Mode & PIL. Added examples
- SAMx scheduler robust to overload
- PICGUI: data visualisation run in background
- MPLAB X project creation is more robust
- dsPIC UART Driver update (typo fixed, robust in idle tasks sending data)
- dsPIC EV watch dog setting fixed
- Task State block fixed pin settinf for SAMx
- Update makefile with R2020b template
- dsPIC 30f default fuse value is not 1 by default. Write all fuses
- dsPIC CK/CH fixed code replacement FastMemCpy implementation
- dsPIC CCPx timer typo for some blocks that use timer
- Updated PIC32 IPL switch function
-
v3.48:
- Added SPI & I2C for SAMx5 family
- ADC for SAMx5: fixed AIN0 channel input not working
- Added support for 64 bit MPLAB X Ide (v5.45 and above)
- Fixed I2C & SPI register names for some dsPICs (EV, FJ)
- dsPIC Change Notification / Input Capture: Fixed GUI Error when copy-past block to a model with a different chip
- Relaxed conditions triggering SINCOS Code Replacement.
-
v3.47.00:
- Added SPI support for dsPIC GS, CH, CK
- Fixed pin mapping inconsistency on dualcore dsPIC for Secondary Core
- Fixed generic issue with former Matlab release
- Fixed MPLAB X project creation with R2019a
-
v3.46.064:
- Improved SAMx5 support. Added SPI support
- Fixed issue with dual core dsPIC support. Renamed core appelation with Main and Secondary.
- Fixed MPLAB X project not created with R2020b
- Added PIC32 GPK MCG and GPG
-
v3.46.063:
- Support for SAMx5 familly
- Fixed search issue for recent XC compilers
- Support external CMSIS and DFP packages
- Renamed scripts pad and padr to picgui.pad/padr (Conflict with MathWorks scripts on recent versions)
-
v3.46.05:
- Fixed compiling issue when using a model reference block (compiling submodel as a library)
-
v3.46.04:
- PIC32: Extend limited choice for output pin function (Pin mapping)
-
v3.46.03:
- fixed Java related issue with programmer interface
-
v3.46.02:
- SPI fixed DMA support for PIC32. Added 8 bit mode with DMA enabled for dsPIC
-
v3.46.01:
- Programmer interface (Java might not be found)
- SAMx7 chip issues with doc block ; MPLAB X project
- Installer script propose old installation method (might fix add-ons issues related to user permissions in classroom/lab configuration)
-
v3.46.00:
- Added support for dual core dsPIC CH
-
v3.45.05:
- Fixed QEI typo in generated code (PIC32MK)
- fixed SPI typo affecting slave mode (PIC32)
-
v3.45.04:
- Fixed possible issue with MPLAB X project creation with model targeting PIC32
- Fixed Typo on Timer code generator for PIC32 (project not compiling when problem occurs)
- Added an External Mode example for PIC32MZ + minor update on other example and script compiling all models
-
v3.45.03:
- Fixed wrong heap linker flag at command line for PIC32 when using Compiler Option block
- Fixed PIL and External Mode GUI not showing the model UART block settings.
-
v3.45.02:
- Added IPE or MDB choice for programming (previously automatically selected)
- Added support for comparator for dsPIC33FJxxMC 02/06
- Added support for SNAP and PICKIT 4 programmer with MDB interface
- Removed files generated by programmer interface (MDB or IPE) in working folder.
- Fixed some issue with SAMx70 and SAMx71 family
- Reduced Wait State for SAMV
- Updated motor example for SAME70 PIM with MCLV2 board
- Added missing dsPIC33CK
- Improved compatibility with Matlab R2010a
- Extended block GUI text fields which can evaluate workspace variables
- UxV toolbox: improved compatibility with R2010a
Supported MCUs (627)
-
dsPIC30F
- 30F2010
- 30F2011
- 30F2012
- 30F3010
- 30F3011
- 30F3012
- 30F3013
- 30F3014
- 30F4011
- 30F4012
- 30F4013
- 30F5011
- 30F5013
- 30F5015
- 30F5016
- 30F6010
- 30F6011
- 30F6012
- 30F6013
- 30F6014
- 30F6015
-
PIC32MK GPG
- 32MK0256GPG048
- 32MK0256GPG064
- 32MK0512GPG048
- 32MK0512GPG064
-
PIC32MK MCJ
- 32MK0256MCJ048
- 32MK0256MCJ064
- 32MK0512MCJ048
- 32MK0512MCJ064
-
PIC32MK GPK
- 32MK0512GPK064
- 32MK0512GPK100
- 32MK1024GPK064
- 32MK1024GPK100
-
PIC32MK MCF
- 32MK0512MCF064
- 32MK0512MCF100
- 32MK1024MCF064
- 32MK1024MCF100
-
PIC32MK MCM
- 32MK0512MCM064
- 32MK0512MCM100
- 32MK1024MCM064
- 32MK1024MCM100
-
PIC32MZ EFE
- 32MZ0512EFE064
- 32MZ0512EFE100
- 32MZ0512EFE124
- 32MZ0512EFE144
- 32MZ1024EFE064
- 32MZ1024EFE100
- 32MZ1024EFE124
- 32MZ1024EFE144
-
PIC32MZ EFF
- 32MZ0512EFF064
- 32MZ0512EFF100
- 32MZ0512EFF124
- 32MZ0512EFF144
- 32MZ1024EFF064
- 32MZ1024EFF100
- 32MZ1024EFF124
- 32MZ1024EFF144
-
PIC32MZ EFK
- 32MZ0512EFK064
- 32MZ0512EFK100
- 32MZ0512EFK124
- 32MZ0512EFK144
- 32MZ1024EFK064
- 32MZ1024EFK100
- 32MZ1024EFK124
- 32MZ1024EFK144
-
PIC32MZ EFG
- 32MZ1024EFG064
- 32MZ1024EFG100
- 32MZ1024EFG124
- 32MZ1024EFG144
- 32MZ2048EFG064
- 32MZ2048EFG100
- 32MZ2048EFG124
- 32MZ2048EFG144
-
PIC32MZ EFH
- 32MZ1024EFH064
- 32MZ1024EFH100
- 32MZ1024EFH124
- 32MZ1024EFH144
- 32MZ2048EFH064
- 32MZ2048EFH100
- 32MZ2048EFH124
- 32MZ2048EFH144
-
PIC32MZ EFM
- 32MZ1024EFM064
- 32MZ1024EFM100
- 32MZ1024EFM124
- 32MZ1024EFM144
- 32MZ2048EFM064
- 32MZ2048EFM100
- 32MZ2048EFM124
- 32MZ2048EFM144
-
dsPIC33CH MP
- 33CH1024MP305
- 33CH1024MP306
- 33CH1024MP308
- 33CH1024MP405
- 33CH1024MP406
- 33CH1024MP408
- 33CH1024MP410
- 33CH1024MP412
- 33CH1024MP605
- 33CH1024MP606
- 33CH1024MP608
- 33CH1024MP705
- 33CH1024MP706
- 33CH1024MP708
- 33CH1024MP710
- 33CH1024MP712
- 33CH128MP202
- 33CH128MP203
- 33CH128MP205
- 33CH128MP206
- 33CH128MP208
- 33CH128MP502
- 33CH128MP503
- 33CH128MP505
- 33CH128MP506
- 33CH128MP508
- 33CH256MP205
- 33CH256MP206
- 33CH256MP208
- 33CH256MP218
- 33CH256MP505
- 33CH256MP506
- 33CH256MP508
- 33CH512MP205
- 33CH512MP206
- 33CH512MP208
- 33CH512MP305
- 33CH512MP306
- 33CH512MP308
- 33CH512MP405
- 33CH512MP406
- 33CH512MP408
- 33CH512MP410
- 33CH512MP412
- 33CH512MP505
- 33CH512MP506
- 33CH512MP508
- 33CH512MP605
- 33CH512MP606
- 33CH512MP608
- 33CH512MP705
- 33CH512MP706
- 33CH512MP708
- 33CH512MP710
- 33CH512MP712
- 33CH64MP202
- 33CH64MP203
- 33CH64MP205
- 33CH64MP206
- 33CH64MP208
- 33CH64MP502
- 33CH64MP503
- 33CH64MP505
- 33CH64MP506
- 33CH64MP508
-
dsPIC33CK MP
- 33CK1024MP405
- 33CK1024MP406
- 33CK1024MP408
- 33CK1024MP410
- 33CK1024MP705
- 33CK1024MP706
- 33CK1024MP708
- 33CK1024MP710
- 33CK128MP202
- 33CK128MP203
- 33CK128MP205
- 33CK128MP206
- 33CK128MP208
- 33CK128MP502
- 33CK128MP503
- 33CK128MP505
- 33CK128MP506
- 33CK128MP508
- 33CK256MP202
- 33CK256MP203
- 33CK256MP205
- 33CK256MP206
- 33CK256MP208
- 33CK256MP305
- 33CK256MP306
- 33CK256MP308
- 33CK256MP405
- 33CK256MP406
- 33CK256MP408
- 33CK256MP410
- 33CK256MP502
- 33CK256MP503
- 33CK256MP505
- 33CK256MP506
- 33CK256MP508
- 33CK256MP605
- 33CK256MP606
- 33CK256MP608
- 33CK256MP705
- 33CK256MP706
- 33CK256MP708
- 33CK256MP710
- 33CK32MP102
- 33CK32MP103
- 33CK32MP105
- 33CK32MP202
- 33CK32MP203
- 33CK32MP205
- 33CK32MP206
- 33CK32MP502
- 33CK32MP503
- 33CK32MP505
- 33CK32MP506
- 33CK512MP305
- 33CK512MP306
- 33CK512MP308
- 33CK512MP405
- 33CK512MP406
- 33CK512MP408
- 33CK512MP410
- 33CK512MP605
- 33CK512MP606
- 33CK512MP608
- 33CK512MP705
- 33CK512MP706
- 33CK512MP708
- 33CK512MP710
- 33CK64MP102
- 33CK64MP103
- 33CK64MP105
- 33CK64MP202
- 33CK64MP203
- 33CK64MP205
- 33CK64MP206
- 33CK64MP208
- 33CK64MP502
- 33CK64MP503
- 33CK64MP505
- 33CK64MP506
- 33CK64MP508
-
dsPIC33CK MC
- 33CK128MC102
- 33CK128MC103
- 33CK128MC105
- 33CK128MC106
- 33CK128MC502
- 33CK128MC503
- 33CK128MC505
- 33CK128MC506
- 33CK256MC102
- 33CK256MC103
- 33CK256MC105
- 33CK256MC106
- 33CK256MC502
- 33CK256MC503
- 33CK256MC505
- 33CK256MC506
- 33CK32MC102
- 33CK32MC103
- 33CK32MC105
- 33CK64MC102
- 33CK64MC103
- 33CK64MC105
-
dsPIC33CK MPT
- 33CK256MPT608
- 33CK512MPT608
-
dsPIC33EP GM
- 33EP128GM304
- 33EP128GM306
- 33EP128GM310
- 33EP128GM604
- 33EP128GM706
- 33EP128GM710
- 33EP256GM304
- 33EP256GM306
- 33EP256GM310
- 33EP256GM604
- 33EP256GM706
- 33EP256GM710
- 33EP512GM304
- 33EP512GM306
- 33EP512GM310
- 33EP512GM604
- 33EP512GM706
- 33EP512GM710
-
dsPIC33EP GP
- 33EP128GP502
- 33EP128GP504
- 33EP128GP506
- 33EP256GP502
- 33EP256GP504
- 33EP256GP506
- 33EP32GP502
- 33EP32GP503
- 33EP32GP504
- 33EP512GP502
- 33EP512GP504
- 33EP512GP506
- 33EP512GP806
- 33EP64GP502
- 33EP64GP503
- 33EP64GP504
- 33EP64GP506
-
dsPIC33EP GS
- 33EP128GS702
- 33EP128GS704
- 33EP128GS705
- 33EP128GS706
- 33EP128GS708
- 33EP128GS804
- 33EP128GS805
- 33EP128GS806
- 33EP128GS808
- 33EP16GS202
- 33EP16GS502
- 33EP16GS504
- 33EP16GS505
- 33EP16GS506
- 33EP32GS202
- 33EP32GS502
- 33EP32GS504
- 33EP32GS505
- 33EP32GS506
- 33EP64GS502
- 33EP64GS504
- 33EP64GS505
- 33EP64GS506
- 33EP64GS708
- 33EP64GS804
- 33EP64GS805
- 33EP64GS806
- 33EP64GS808
-
dsPIC33EP MC
- 33EP128MC202
- 33EP128MC204
- 33EP128MC206
- 33EP128MC502
- 33EP128MC504
- 33EP128MC506
- 33EP256MC202
- 33EP256MC204
- 33EP256MC206
- 33EP256MC502
- 33EP256MC504
- 33EP256MC506
- 33EP32MC202
- 33EP32MC203
- 33EP32MC204
- 33EP32MC502
- 33EP32MC503
- 33EP32MC504
- 33EP512MC202
- 33EP512MC204
- 33EP512MC206
- 33EP512MC502
- 33EP512MC504
- 33EP512MC506
- 33EP512MC806
- 33EP64MC202
- 33EP64MC203
- 33EP64MC204
- 33EP64MC206
- 33EP64MC502
- 33EP64MC503
- 33EP64MC504
- 33EP64MC506
-
dsPIC33EP MU
- 33EP256MU806
- 33EP256MU810
- 33EP256MU814
- 33EP512MU810
- 33EP512MU814
-
dsPIC33EV GM
- 33EV128GM002
- 33EV128GM003
- 33EV128GM004
- 33EV128GM006
- 33EV128GM102
- 33EV128GM103
- 33EV128GM104
- 33EV128GM106
- 33EV256GM002
- 33EV256GM003
- 33EV256GM004
- 33EV256GM006
- 33EV256GM102
- 33EV256GM103
- 33EV256GM104
- 33EV256GM106
- 33EV32GM002
- 33EV32GM003
- 33EV32GM004
- 33EV32GM006
- 33EV32GM102
- 33EV32GM103
- 33EV32GM104
- 33EV32GM106
- 33EV64GM002
- 33EV64GM003
- 33EV64GM004
- 33EV64GM006
- 33EV64GM102
- 33EV64GM103
- 33EV64GM104
- 33EV64GM106
-
dsPIC33FJ GP
- 33FJ128GP202
- 33FJ128GP204
- 33FJ128GP206
- 33FJ128GP206A
- 33FJ128GP306
- 33FJ128GP306A
- 33FJ128GP310
- 33FJ128GP310A
- 33FJ128GP706
- 33FJ128GP706A
- 33FJ128GP708
- 33FJ128GP708A
- 33FJ128GP710
- 33FJ128GP710A
- 33FJ128GP802
- 33FJ128GP804
- 33FJ12GP201
- 33FJ12GP202
- 33FJ16GP304
- 33FJ256GP506
- 33FJ256GP506A
- 33FJ256GP510
- 33FJ256GP510A
- 33FJ256GP710
- 33FJ256GP710A
- 33FJ32GP202
- 33FJ32GP204
- 33FJ32GP302
- 33FJ32GP304
- 33FJ64GP202
- 33FJ64GP204
- 33FJ64GP206
- 33FJ64GP206A
- 33FJ64GP306
- 33FJ64GP306A
- 33FJ64GP310
- 33FJ64GP310A
- 33FJ64GP706
- 33FJ64GP706A
- 33FJ64GP708
- 33FJ64GP708A
- 33FJ64GP710
- 33FJ64GP710A
- 33FJ64GP802
- 33FJ64GP804
-
dsPIC33FJ MC
- 33FJ128MC202
- 33FJ128MC204
- 33FJ128MC506
- 33FJ128MC506A
- 33FJ128MC510
- 33FJ128MC510A
- 33FJ128MC706
- 33FJ128MC706A
- 33FJ128MC708
- 33FJ128MC708A
- 33FJ128MC710
- 33FJ128MC710A
- 33FJ128MC802
- 33FJ128MC804
- 33FJ12MC201
- 33FJ12MC202
- 33FJ16MC304
- 33FJ256MC510
- 33FJ256MC510A
- 33FJ256MC710
- 33FJ256MC710A
- 33FJ32MC202
- 33FJ32MC204
- 33FJ32MC302
- 33FJ32MC304
- 33FJ64MC202
- 33FJ64MC204
- 33FJ64MC506
- 33FJ64MC506A
- 33FJ64MC508
- 33FJ64MC508A
- 33FJ64MC510
- 33FJ64MC510A
- 33FJ64MC706
- 33FJ64MC706A
- 33FJ64MC710
- 33FJ64MC710A
- 33FJ64MC802
- 33FJ64MC804
-
PIC32
- PIC32CM1216MC00032
- PIC32CM1216MC00048
- PIC32CM6408MC00032
- PIC32CM6408MC00048
-
SAMC20
- SAMC20E15A
- SAMC20E16A
- SAMC20E17A
- SAMC20E18A
- SAMC20G15A
- SAMC20G16A
- SAMC20G17A
- SAMC20G18A
- SAMC20J15A
- SAMC20J16A
- SAMC20J17A
- SAMC20J17AU
- SAMC20J18A
- SAMC20J18AU
- SAMC20N17A
- SAMC20N18A
-
SAMC21
- SAMC21E15A
- SAMC21E16A
- SAMC21E17A
- SAMC21E18A
- SAMC21G15A
- SAMC21G16A
- SAMC21G17A
- SAMC21G18A
- SAMC21J15A
- SAMC21J16A
- SAMC21J17A
- SAMC21J17AU
- SAMC21J18A
- SAMC21J18AU
- SAMC21N17A
- SAMC21N18A
-
SAMD20
- SAMD20E14
- SAMD20E14B
- SAMD20E15
- SAMD20E15B
- SAMD20E15BU
- SAMD20E16
- SAMD20E16B
- SAMD20E16BU
- SAMD20E17
- SAMD20E18
- SAMD20E1F
- SAMD20G14
- SAMD20G14B
- SAMD20G15
- SAMD20G15B
- SAMD20G16
- SAMD20G16B
- SAMD20G17
- SAMD20G17U
- SAMD20G18
- SAMD20G18U
- SAMD20J14
- SAMD20J14B
- SAMD20J15
- SAMD20J15B
- SAMD20J16
- SAMD20J16B
- SAMD20J17
- SAMD20J18
-
SAMD21
- SAMD21E15A
- SAMD21E15B
- SAMD21E15BU
- SAMD21E15CU
- SAMD21E15L
- SAMD21E16A
- SAMD21E16B
- SAMD21E16BU
- SAMD21E16CU
- SAMD21E16L
- SAMD21E17A
- SAMD21E17D
- SAMD21E17DU
- SAMD21E17L
- SAMD21E18A
- SAMD21F17L
- SAMD21G15A
- SAMD21G15B
- SAMD21G15L
- SAMD21G16A
- SAMD21G16B
- SAMD21G16L
- SAMD21G17A
- SAMD21G17AU
- SAMD21G17D
- SAMD21G17L
- SAMD21G18A
- SAMD21G18AU
- SAMD21J15A
- SAMD21J15B
- SAMD21J16A
- SAMD21J16B
- SAMD21J17A
- SAMD21J17D
- SAMD21J18A
-
SAME51
- SAME51G18A
- SAME51G19A
- SAME51J18A
- SAME51J19A
- SAME51J20A
- SAME51N19A
- SAME51N20A
-
SAME53
- SAME53J18A
- SAME53J19A
- SAME53J20A
- SAME53N19A
- SAME53N20A
-
SAME54
- SAME54N19A
- SAME54N20A
- SAME54P19A
- SAME54P20A
-
SAME70
- SAME70J19B
- SAME70J20B
- SAME70J21B
- SAME70N19B
- SAME70N20B
- SAME70N21B
- SAME70Q19B
- SAME70Q20B
- SAME70Q21B
-
SAMRH707
- SAMRH707F18A
-
SAMRH71
- SAMRH71F20B
- SAMRH71F20C
-
SAMS70
- SAMS70J19B
- SAMS70J20B
- SAMS70J21B
- SAMS70N19B
- SAMS70N20B
- SAMS70N21B
- SAMS70Q19B
- SAMS70Q20B
- SAMS70Q21B
-
SAMV70
- SAMV70J19B
- SAMV70J20B
- SAMV70N19B
- SAMV70N20B
- SAMV70Q19B
- SAMV70Q20B
-
SAMV71
- SAMV71J19B
- SAMV71J20B
- SAMV71J21B
- SAMV71N19B
- SAMV71N20B
- SAMV71N21B
- SAMV71Q19B
- SAMV71Q20B
- SAMV71Q21B
引用
MPLAB-Device-Blocks-for-Simulink (Microchip Technology)
MATLAB リリースの互換性
プラットフォームの互換性
Windows macOS Linuxタグ
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!blocks
examples
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensored_FOC_Encoder_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensored_PosCtrl_FOC_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensorless_FOC_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_SensorlessObserver_R2015b_dsPIC
examples/SAMV71_MCAN_CfunctionCall
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening/hurstMotor
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening/teknicMotor
examples/University/INSA_Lyon_Ampere_MotorControl/vectorControl
examples/clib
mchp
mchp/+mchppil
mchp/+mchppil_PIC32
mchp/+mchppil_SAMx
mchp/Lib_dsPIC/ASM/src
mchp/Lib_dsPIC/C/src
blocks/blk_mdl
blocks/blk_slx
examples
examples/CRL_Demo
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensored_FOC_Encoder_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensored_PosCtrl_FOC_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_MCB_FOC_SAME70/Sensorless_FOC_PMSM_SAME70_MCLV2
examples/MOTOR_PMSM_SensorlessObserver_R2015b_PIC32MK
examples/MOTOR_PMSM_SensorlessObserver_R2015b_SAME70
examples/MOTOR_PMSM_SensorlessObserver_R2015b_dsPIC
examples/ProcessorIntheLoop_PIL
examples/SAMV71_MCAN_CfunctionCall
examples/SAMV71_Xplained_Ultra_ExtMode_PIL_R2020b
examples/SAMx7_Xplained_EEPROM
examples/UART_Terminal
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening/hurstMotor
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening/teknicMotor
examples/University/INSA_Lyon_Ampere_MotorControl/vectorControl
doc
examples/University/INSA_Lyon_Ampere_MotorControl/fieldWeakening
GitHub の既定のブランチを使用するバージョンはダウンロードできません
バージョン | 公開済み | リリース ノート | |
---|---|---|---|
3.54 | See release notes for this release on GitHub: https://github.com/MPLAB-Blockset/MPLAB-Device-Blocks-for-Simulink/releases/tag/v3.54 |
|
|
3.52 | See release notes for this release on GitHub: https://github.com/MPLAB-Blockset/MPLAB-Device-Blocks-for-Simulink/releases/tag/v3.52 |
|
|
3.50 | -Add SAMC2x SAMD2x SAMDAx
|
|
|
3.49 | - External-Mode & PIL
|
|
|
3.48 | - Added SPI & I2C for SAMx5
|
|
|
3.47 | - Added SPI support for dsPIC GS, CH, CK
|
|
|
3.46.064 | - Improved SAMx5 support. Added SPI support
|
|
|
3.46.063 | - Support for SAMx5 familly
|
|
|
3.46.05 | PIC32: extend option for peripheral output pin (Peripheral Pin mapping)
|
|
|
3.46.03 | - Updated PIC32MZ SPI DMA implementation
|
|
|
3.46.01 | - Programmer interface (Java might not be found)
|
|
|
3.46.00 | Support added for dsPIC CH dual core DSCs |
|
|
3.45.05 | - fixed QEI typo in generated code (PIC32)
|
|
|
3.45.04 | Fixes:
- Improved MPLAB X project creation
|
|
|
3.45.02 | - Extended supported chip
|
|
|
3.45.01 | Updated installer. Compatible from R2010a to R2019a |
|
|
3.45 |
|