結果:
Hi I have a user defined blocks for my Simulink but whenever I add path of user defined, the error pops up stating I dont have stateflow.
Can anyone please guide me through it.
Hello! I am wondering if it is possible to connect ls-dyna to matlab so that when i enter the parameters on matlab, ls-dyna reads the parameter from and runs the simulation and sends the result to matlab.
let me know if there's any more info needed, good solution or whether it is even possible
Dear all,
I would like to know if "Ridge regularization, i.e., L2" is applicable to the LSBoost regression model or not. After searching the MATLAB documentation, I found code only for "Lasso (L1) regularization."
For example:
t = templateTree(Reproducible=true);
bag = fitrensemble(X,Y,Method="Bag",NumLearningCycles=300,Learners=t);
bag = regularize(bag,Lambda=[0.001 0.1],Verbose=1);
Best regards,
Hello, I have applied the "sobel" edge detection function. However, I am not sure how to segment and single out only the cells that contain the " cross" shape inside of them. These are the cells infected by Babesisos, while the rest are not infected.
Thanks !
Hello everyone,
I am trying to simulate the trajectory of a two-stage rocket in Simulink. I am using the 'Custom Variable Mass 6DOF ECEF (Quaternion) Equation of Motion'. I would like to use a PID controller to control the pitch angle of the rocket (note, pitch angle is the output). The issue is that the above Equation of Motion is non-linear. Is there a way to linearize this EOM for the entire trajectory? the system is time dependent ( as the mass, velocity and trajectory changes with time).
link of the EoM:
https://nl.mathworks.com/help/aeroblks/customvariablemass6dofecefquaternion.html
hi
I have a problem when offline installing the support packages for the zynq on matlab r2019a.
I obtain the following error message:
"Support Software Installer Error
System does not have the required MATLAB version to start the support package installation."
I tried different versions, uninstall/re-install matlab, different ways for installing this package and it does not work
Do you have any suggestions
I'm getting an error error "using tall/cellfun" while doing a project listed in mathworks "Denoise Speech Using Deep Learning Networks". I don't know how to fix this error pr why this error occured in the first place. Seeking explanation for this particuar error. If you know anuthing about it then please consider helping me below this post.
Hello, all!
This is my first post after just joining this discussion, so please forgive me and provide kind assistance if I have posted to the wrong subsection!
I have a good interest in learning sql server course and right now I am taking help from various platforms like https://www.coursera.org/ https://www.udemy.com/
Also I have a doubt that is it a good option to learn from platforms like this or I should go for some sql server online training . I have searched for the solution of my queries in various above platforms which helped me up to some extent only as it was not directly given by any expert or trainer.
Hoping in getting a quick response
Thankyou in advance.
Hello, I am a student and I am working on a neural network for a line follower car and I would like you to recommend a tutorial to implement it in simulink.
Hello, everyone.
I have got the x,y,z coordinates and MagE for a radiation pattern. But when I want to plot it in spherical coordinates using 'patternCustom' function, I found the pattern is incomplete.
I attaced the data and script here. Can someone help me?
Hello everyone !!!!
I try to develop a test bench for cybersecurity in micro grids (Generations, Breakers,...) . I plan to simulate my grid on Simpower. I have a simulated PLC in a VM and a real RTAC. I would like to establish bidirectional communication between my grid simulated on Simpower and the physical RTAC (or the simulated PLC on VM). The RTAC is connected to a SCADA system which should be able to send commands to the grid (Simpower).
RTAC, Simpower, and the SCADA system are located on separate machines.
Any approach to establish a connection between Simpower and the RTAC (or PLC)?
Thanks !!!
I think it would be a really great feature to be able to add an Alpha property to the basic "Line" class in MATLAB plots. I know that I have previously had to resort to using Patch to be able to plot semitransparent lines, but there are also so many other functions that rely on the "Line" class.
For example, if you want to make a scatter plot from a table with things specified into groups, you can use ScatterHistogram or gscatter but since gscatter uses the Line class, you can't adjust the marker transparency. So if you don't want the histograms, you are stuck with manually separating it and using scatter with hold on.
Hello! I'm currently working on a heat transfer problem, I don't consider myself to be an expert, therefore I'm still learning how to use this tool.
Here's the thing: I have pretty much everything working, but there's an issue. The ELSE equation is not giving any results and I don't know exactly why. I would appreciate if someone would be interested in helping me learn about this because I'm at a loss righ now
%% Parámetros geométricos del dominio
A=3; %Anchura (en metros)
H=2.5; %Altura (en metros)
Nx= 7; %Número de nodos en la dirección x
Ny=6; %Número de nodos en la dirección y
dx=A/(Nx-1); %Distancia de elemento finito en dirección x (metros)
dy=H/(Ny-1); %Distancia de elemento finito en direccion y (metros)
%% Condiciones iniciales y de frontera
To=1000; %Temperatura interna del horno (en C)
T = ones(Nx,Ny);
Tinf=20; %Temperatura externa (en C)
ho=100; %Coeficiente de transferencia convectiva interior (en W/m^2K)
hinf=10; %Coeficiente de transferencia convectiva exterior (en W/m^2K)
q_dot=8000; %Calor generado por unidad volumétrica
K=1; %Conductividad del material (en W/mK)
epsilon=1e-5;
Error=5;
%% Computación
iter=0;
while (Error>epsilon)
iter=iter+1;
disp(iter);
Told=T;
for j=1:Ny
for i=1:Nx
if i==Nx
for j=2:Ny-1
T(i,j)=(2*T(i-1,j)+T(i,j-1)+T(i,j+1)+(q_dot*dx^2)/K)/4;
end
for j=Ny
T(i,j)=T(i,j-1)+T(i-1,j)+(q_dot*dx^2)/(2*K)+(hinf*dx*Tinf)/K;
end
for j=1
T(i,j)=((q_dot*dx^2)/(2*K)+T(i-1,j)+T(i,j+1));
end
elseif i==1
for j=Ny*4/6:Ny-1
T(i,j)=(2*T(i+1,j)+T(i,j-1)+T(i,j+1)+(q_dot*dx^2)/K)/4;
end
for j=Ny*0.5
T(i,j)=T(i,j+1)+T(i+1,j)+(q_dot*dx^2)/(2*K)+(hinf*dx*Tinf)/K;
end
for j=Ny
T(i,j)=T(i,j-1)+T(i+1,j)+(q_dot*dx^2)/(2*K)+(ho*dx*To)/K;
end
elseif i>1 && i<Nx
for j=Ny
T(i,j)=(T(i-1,j)+T(i+1,j)+2*T(i,j-1)+(q_dot*dx^2)/K+(2*hinf*dx*Tinf)/K)/(4+2*hinf*dx/K);
end
elseif 2<i && i<Nx*3/7
for j=Ny*0.5
T(i,j)=((T(i-1,j)+T(i+1,j)+2*T(i,j+1)+(q_dot*dx^2)/K)+(2*ho*dx*To)/K)/(4+2*hinf*dx/K);
end
elseif i==Nx*4/7
for j=2:Ny*2/6
T(i,j)=((T(i,j-1)+T(i-j+1)+2*T(i+1,j)+(q_dot*dx^2)/K)+(2*ho*dx*To)/K)/(4+2*hinf*dx/K);
end
for j=1
T(i,j)=T(i,j-1)+T(i+1,j)+(q_dot*dx^2)/(2*K)+(ho*dx*To)/K;
end
for j=Ny*0.5
T(i,j)=(T(i,j+1)+2*T(i+1,j)+2*T(i,j+1)+T(i-1,j)+(3*q_dot*dx^2)/(2*K)+(2*ho*dx*To)/K)/(6+(2*ho*dx)/K);
end
else
T(i,j)=(T(i-1,j)+T(i+1,j)+T(i,j-1)+T(i,j+1)+(q_dot*dx^2)/K)/4;
end
end
end
Error=sqrt(sumsqr(T-Told));
disp(Error);
end
T(1:3,1) = To;
T(1:3,2)=To;
%% Graficando el resultado
x=0:dx:A;
y=0:dy:H;
% Definir los límites de color para resaltar variaciones
min_temp = min(min(T)); % Obtener el valor mínimo de temperatura
max_temp = max(max(T)); % Obtener el valor máximo de temperatura
colormap(hot); % Cambiar el colormap (puedes probar otros)
contourf(x, y, T', 'LineWidth', 1); % Añadir un grosor de línea para los contornos
colorbar;
title('Distribución de Temperatura')
xlabel('Dirección en x')
ylabel('Dirección en y')
% Establecer los límites de color para resaltar variaciones
clim([min_temp, max_temp]); % Establecer los límites de color según los valores mínimos y máximos de temperatura
Matlab show me that the next problem.
Tie variable 'Pressure_Transducer_Timpano.p.v' (Voltage) to a definite value, for example by connecting an appropriate domain reference block.
I don't know what I should do in it because I have done an model by hearing and use this object because I want to modelate a Timpanumm membrane. If you could help I really gratefully.
I will include the picture.
Hi, I'm in truble because I have two programs with the same variables and parameters. The main of the study is to change a value and plot the results. The problem is that I want them on the same plot but I use the same name for the variabes in the two different programs so when I use some function to join the figures togheter matlab resets the values obtained in the first program and runs only the second one.
Is there a method to avoid changing all the names of the variables in one of the two programs (because they have something like 500 lines)?
Hi everyone,
I would like to ask you if it would be possible to do an HiL simulation using an environment model simulated via Simulink and load in a target computer connected to the hardware needed. The target computer will be simply a laptop with Matlab&Simulink package installed and directly connected to the bench to test.
I have found some solutions about the use of Simulink Real-Time but it implies the use of a Speedgoat unit, so I was wondering if anyone has ever done it without that device.
Thank you very much.
Hi, I'm trying to analyze a .vtk data set from MRI. I already calculate the kinetic energy. Now I'm trying to calculate the viscous energy loss but the result that I found does not respect the reality so I think that I'm doing something wrong.
Can someone help me with this?
%% FUNCTION
function energy_loss = calculateViscousEnergyLossForAllPhases(MRI_Velocity, dynamic_viscosity,interval)
% Preallocate the energy_dissipation array
energy_loss = zeros(1, 30);
for idx_phase = 1:30
% Velocity field
vel_x = MRI_Velocity{1, idx_phase}.velocity(:,1) * 1e-2; % Velocity in X from cm/s to m/s
vel_y = MRI_Velocity{1, idx_phase}.velocity(:,2) * 1e-2; % Velocity in Y in m/s
vel_z = MRI_Velocity{1, idx_phase}.velocity(:,3) * 1e-2; % Velocity in Z in m/s
% Coordinates
x = MRI_Velocity{1, idx_phase}.points(:,1) * 1e-3; % from mm to m
y = MRI_Velocity{1, idx_phase}.points(:,2) * 1e-3;
z = MRI_Velocity{1, idx_phase}.points(:,3) * 1e-3;
% Compute partial derivatives
dUdx = gradient(vel_x, x, 1);
dUdy = gradient(vel_x, y, 2);
dUdz = gradient(vel_x, z, 3);
dVdx = gradient(vel_y, x, 1);
dVdy = gradient(vel_y, y, 2);
dVdz = gradient(vel_y, z, 3);
dWdx = gradient(vel_z, x, 1);
dWdy = gradient(vel_z, y, 2);
dWdz = gradient(vel_z, z, 3);
% Calculate energy dissipation
ED = 2 * (dUdx.^2 + dUdy.^2 + dUdz.^2) + ...
2 * (dVdx.^2 + dVdy.^2 + dVdz.^2) + ...
2 * (dWdx.^2 + dWdy.^2 + dWdz.^2) + ...
(dUdz + dWdx).^2 + (dVdx + dUdy).^2 + (dWdy + dVdz).^2;
% Scale by dynamic viscosity of fluid and store
energy_loss(idx_phase) = sum(ED, 'all', 'omitnan') * dynamic_viscosity * interval.^3;
end
end
%% CODE
dynamic_viscosity_blood = 0.0039;
% human dynamic_viscosity_blood from 0.003 to 0.004; % Approximate value for blood at body temperature
% Call the function to calculate viscous energy loss for blood flow for all phases
energy_loss_RV_J = calculateViscousEnergyLossForAllPhases(MRI_Velocity_RV, dynamic_viscosity_blood,interval/1000);
energy_loss_LV_J = calculateViscousEnergyLossForAllPhases(MRI_Velocity_LV, dynamic_viscosity_blood,interval/1000);
% From Joule to milliwatt (mW)
energy_loss_RV_mW = energy_loss_RV_J.*1e3;
energy_loss_LV_mW = energy_loss_LV_J.*1e3;
figure
plot(time, energy_loss_RV_mW, 'r','LineWidth',1.5);
hold on
plot(time, energy_loss_LV_mW,'b','LineWidth',1.5);
title('Viscous energy loss over Cycle','FontSize',14);
xlabel('Cycle','FontSize',12);
ylabel('Viscous energy loss [mW]','FontSize',12);
legend('RV','LV')
Hi Guys
Posting this based on a thought I had, so I don't really ahve any code however I would like to know if the thought process is correct and/or relatively accurate.
Consider a simple spring mass system which only allows compression on the spring however when there is tension the mass should move without the effect of the spring distrupting it, thus the mass is just thrown vertically upwards.
The idea which I came up with for such a system is to have two sets of dfferential equations, one which represents the spring system and another which presents a mass in motion without the effects of the spring.
Please refer to the below basic outline of the code which I am proposing. I believe that this may produce relatively decent results. The code essentially checks if there is tension in the system if there is it then takes the last values from the spring mass differential equation and uses it as initial conditions for the differential equation with the mass moving wothout the effects of the spring, this process works in reverse also. The error which would exist is that the initial conditions applied to the system would include effects of the spring. Would there be a better way to code such behaviour?
function xp = statespace(t,x,f,c,k,m)
if (k*x(1)) positive #implying tension
**Use last time step as initial conditions**
**differential equation of a mass moving""
end
if x(1) negative #implying that the mass in now moving down therefore compression in spring
**Use last time step as initial conditions**
**differential equation for a spring mass system**
end
end
Hi Friends,
I'm looking for a matlab program which calculat deflection of simply supported tapered beam under uniform travers load.
Thank you for your help.
Hello, how can i write a combination of matrcies as follows L=[ai_j] of order 4,M of order 4, then S=[4*ai_j+M] of order 4. i mean each element in S is a matrex of order 4
