General Flexible Plate
Libraries:
Simscape /
Multibody /
Body Elements /
Flexible Bodies /
Plates and Shells
Description
The General Flexible Plate block models thin, flat structure capable of elastic deformations, including stretch, bending, and shear effects. The block applies the shear deformation Mindlin plate theory [1][2][3] and uses the finite element method [4] for its solution. You can use this block to model thin, flat structures, such as linkages and satellite solar panels.
To specify the geometry of a plate, use the Midsurface and Thickness parameters. The midsurface of the plate is in the xy plane and the thickness is along the z axis. The thickness must be much smaller than the width and length of the plate, and the plate is symmetric about the midsurface. See the Geometry section for more details.
The block models a flexible plate made of homogeneous, isotropic, and linearly elastic materials. You can specify the density, Young's modulus, and Poisson's ratio or shear modulus of the plate in the Stiffness and Inertia section. Additionally, the block supports two damping methods to control the performance of the modeling. To add custom frames to the plate, specify parameters in the Frames section.
Ports
Frame
FN — Custom frame
frame
Custom body-attached frames. Specified the name of the port using the New Frame parameter. If you do
not specify the name of the custom frame, the block names the frame
FN, where N
is an identifying number.
Dependencies
To enable a custom frame port, create a frame by clicking New Frame.
Parameters
Geometry
Midsurface — Coordinates of plate midsurface
[1 1; -1 1; -1 -1; 1 -1] m
| N-by-2 matrix | M-by-1 or 1-by-M cell array of
N-by-2 matrices
Coordinates used to specify the midsurface boundaries of the plate on the local xy plane. You can specify the midsurface by using:
An N-by-2 matrix of xy coordinates to specify a midsurface. Each row gives the [x,y] coordinates of a point on the mid-surface boundaries. The points connect in the specified order to form a closed polyline. To ensure that the polyline is closed, the block inserts a line segment between the last and first points.
An M-by-1 or 1-by-M cell array of N-by-2 matrices of xy coordinates to specify a midsurface with holes. The first element in the array represents the outer boundary and subsequent elements specify the hole boundaries.
Note
Ensure that any two boundaries do not intersect, overlap, or touch.
Additionally, each individual boundary must have:
No repeated vertices
No self-intersections
At least three non-collinear points
Thickness — Plate thickness
0.1 m
(default) | positive scalar
Thickness of the plate. The block models the plate by extruding the specified midsurface along the local z axis of the plate. The extrusion is symmetric about the local xy plane of the pate. The thickness should be much smaller than the overall midsurface dimensions for plate theory to apply.
Stiffness and Inertia
Density — Mass per unit volume of material
2700 kg/m^3
(default) | positive scalar
Mass per unit volume of material. The default value corresponds to aluminum.
Specify — Elastic properties used to parameterize plate
Young's Modulus and Poisson's Ratio
(default) | Young's and Shear Modulus
Elastic properties used to parameterize the plate. You can specify either
Young's Modulus and Poisson's Ratio
or Young's and Shear
Modulus
. These properties are commonly available in materials
databases.
Young's Modulus — Ratio of axial stress to axial strain
70 GPa
(default) | positive scalar
Young's modulus of the elasticity of the plate. The greater the value of this parameter, the stronger the resistance to bending and in-plane normal deformation. The default value corresponds to aluminum.
Poisson's Ratio — Ratio of transverse to normal strains
0.33 (default) | scalar in the range [0, 0.5)
Poisson's ratio of the plate. The value specified must be greater than or equal to 0 and smaller than 0.5. The default value corresponds to aluminum.
Dependencies
To enable this parameter, set Specify to Young's
Modulus and Poisson's Ratio
.
Shear Modulus — Ratio of shear stress to engineering shear strain
26 GPa
(default) | positive scalar
Shear modulus, also known as the modulus of rigidity, of the plate. The larger value correlates to a stronger resistance to shearing and twisting. The default value corresponds to aluminum.
Dependencies
To enable this parameter, set Specify to Young's
and Shear Modulus
.
Damping
Type — Type of damping method
Proportional
(default) | Uniform Modal
| None
Damping method for the plate:
Select
None
to model undamped plates.Select
Proportional
to apply the proportional (or Rayleigh) damping method. This method defines the damping matrix [C] as a linear combination of the mass matrix [M] and stiffness matrix [K]:,
where α and β are the scalar coefficients.
Select
Uniform Modal
to apply the uniform modal damping method. This method applies a single damping ratio to all the vibration modes of the plate. The larger the value, the faster vibrations decay.
Mass Coefficient — Coefficient of mass matrix
0 1/s
(default) | nonnegative scalar
Coefficient α of the mass matrix. This parameter defines damping proportional to the mass matrix [M].
Dependencies
To enable this parameter, set Type to
Proportional
.
Stiffness Coefficient — Coefficient of stiffness matrix
0.001 s
(default) | nonnegative scalar
Coefficient β of the stiffness matrix. This parameter defines damping proportional to the stiffness matrix [K].
Dependencies
To enable this parameter, set Type to
Proportional
.
Damping Ratio — Damping ratio for uniform modal damping method
0.01 (default) | unitless nonnegative scalar
Damping ratio ζ applied to all vibration modes of a plate. The larger the value, the faster vibrations decay. The vibration modes are underdamped if ζ < 1 and overdamped if ζ > 1.
Dependencies
To enable this parameter, set Type to Uniform
Modal
.
Data Types: double
Fidelity
Reduction — Method to model flexible bodies
None
(default) | Modally Reduced
Method to use to model flexible bodies, specified as
None
or Modally Reduced
. Set
the parameter to None
to use full nodal elastic coordinates
generated by the finite-element method or set the parameter to Modally
Reduced
to use the modal transformation method to reduce the elastic
coordinates of the body. For both settings, the block uses the floating frame of the
reference formulation [5-6] to couple the body with its elastic deformation.
Number of Retained Modes — Retained modes
1 (default) | nonnegative integer
Retained modes, specified as an integer in range [0, n], where n is the number of elastic degrees of freedom of the body. If you set the number to 0 the flexible body is treated as a rigid body.
Dependencies
To enable this parameter, set Reduction to
Modally Reduced
.
Graphic
Type — Graphic to use in the visualization of plate
From Geometry
(default) | None
Type of the visual representation of the plate, specified as From
Geometry
or None
. Set the parameter to
From Geometry
to show the visual representation of the
plate. Set the parameter to None
to hide the plate in the
model visualization.
Visual Properties — Parameterizations for color and opacity
Simple
(default) | Advanced
Parameterization for specifying visual properties. Select
Simple
to specify color and opacity. Select
Advanced
to specify more visual properties, such as
Specular Color, Ambient Color, Emissive
Color, and Shininess.
Dependencies
To enable this parameter, set Type to From
Geometry
.
Color — Color of light due to diffuse reflection
[0.5 0.5 0.5] (default) | 3-by-1 or 1-by-3 vector with values in the range of 0 to 1 | 4-by-1 or 1-by-4 vector with values in the range of 0 to 1
Color of the graphic under direct white light, specified as an [R G B] or [R G B A] vector on a 0–1 scale. An optional fourth element (A) specifies the color opacity on a scale of 0–1. Omitting the opacity element is equivalent to specifying a value of 1.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Simple
Opacity — Graphic opacity
1.0 (default) | scalar in the range of 0 to 1
Graphic opacity, specified as a scalar in the range of 0 to 1. A scalar of 0 corresponds to completely transparent, and a scalar of 1 corresponds to completely opaque.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Simple
Diffuse Color — Graphic Color
[0.5 0.5 0.5] (default) | three-element vector | three-element vector
Color of the graphic under direct white light, specified as an [R G B] or [R G B A] vector on a 0–1 scale. The optional fourth element specifies the color opacity on a scale of 0–1. Omitting the opacity element is equivalent to specifying a value of 1.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Advanced
Specular Color — Color of light due to specular reflection
[0.5 0.5 0.5 1.0] (default) | 3-by-1 or 1-by-3 vector with values in the range of 0 to 1 | 4-by-1 or 1-by-4 vector with values in the range of 0 to 1
Color of the light due to specular reflection, specified as an [R,G,B] or [R,G,B,A] vector with values in the range of 0 to 1. The vector can be a row or column vector. The optional fourth element specifies the color opacity. Omitting the opacity element is equivalent to specifying a value of 1. This parameter changes the color of the specular highlight, which is the bright spot on the rendered beam due to the reflection of the light from the light source.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Advanced
Ambient Color — Color of ambient light
[0.15 0.15 0.15 1.0] (default) | 3-by-1 or 1-by-3 vector with values in the range of 0 to 1 | 4-by-1 or 1-by-4 vector with values in the range of 0 to 1
Color of the ambient light, specified as an [R,G,B] or [R,G,B,A] vector with values in the range of 0 to 1. The vector can be a row or column vector. The optional fourth element specifies the color opacity. Omitting the opacity element is equivalent to specifying a value of 1.
Ambient light refers to a general level of illumination that does not come directly from a light source. The Ambient light consists of light that has been reflected and re-reflected so many times that it is no longer coming from any particular direction. You can adjust this parameter to change the shadow color of the rendered beam.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Advanced
Emissive Color — Self-illumination color
[0.0 0.0 0.0 1.0] (default) | 3-by-1 or 1-by-3 vector with values in the range of 0 to 1
Color due to self illumination, specified as an [R,G,B] or [R,G,B,A] vector in the range of 0 to 1. The vector can be a row or column vector. The optional fourth element specifies the color opacity. Omitting the opacity element is equivalent to specifying a value of 1.
The emission color is color that does not come from any external source, and therefore seems to be emitted by the beam itself. When a beam has an emissive color, the beam can be seen even if there is no external light source.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Advanced
Shininess — Highlight sharpness
75 (default) | scalar with value constrained to 0–128
Sharpness of specular light reflections, specified as a scalar number on a 0–128 scale. Increase the shininess value for smaller but sharper highlights. Decrease the value for larger but smoother highlights.
Dependencies
To enable this parameter, set:
Type to
From Geometry
Visual Properties to
Advanced
Frames
New Frame — Create custom frame for connection to other blocks
button
Click the Create button to open a pane for creating a new body-attached frame. In this pane, you can specify the name, origin, and orientation for the frame.
To name the custom frame, enter a name in the Frame Name parameter. The name identifies the port on the block and in the tree view pane of the Mechanics Explorer.
Select a frame origin in the Frame Origin section:
At Reference Frame Origin: Make the new frame origin coincident with the origin of the reference frame of the undeformed plate.
Based on Geometric Feature: Make the new frame origin coincident with the center of the selected undeformed geometry feature. Valid features include surfaces, lines, and points. Select a feature from the visualization pane, then click Use Selected Feature button to confirm the location of the origin. The name of the origin location appears in the field below this option.
To define the orientation of the custom frame, under the Frame Axes section, select the Primary Axis and Secondary Axis of the custom frame and then specify their directions.
Use the following methods to select a vector for specifying the directions of the primary and secondary axes. The primary axis is parallel to the selected vector and constrains the remaining two axes to its normal plane. The secondary axis is parallel to the projection of the selected vector onto the normal plane.
Along Reference Frame Axis: Selects an axis of the reference frame of the undeformed plate.
Based on Geometric Feature: Selects the vector associated with the chosen geometry feature of the undeformed plate. Valid features include surfaces and lines. The corresponding vector is indicated by a white arrow in the visualization pane. You can select a feature from the visualization pane and then click Use Selected Feature button to confirm the selection. The name of the selected feature appears in the field below this option.
FrameN — Edit or delete existing custom frame
frame name
Frames that you created. Specified the name of the port using the New Frame parameter. If you do
not specify the name of the custom frame, the block names the frame
FN, where N
is an identifying number.
Click the text field to edit the name of an existing custom frame.
Click the Edit button to edit other aspects of the custom frame, such as the origin and axes.
Click the Delete button to delete the custom frame.
Dependencies
To enable this parameter, create a frame by clicking New Frame.
References
[1] Bathe, Klaus-Jürgen. Finite Element Procedures. 2nd ed. Englewood Cliffs, N.J: Prentice-Hall, 2014.
[2] Cook, Robert Davis. Concepts and Applications of Finite Element Analysis. 4th ed. New York, NY: Wiley, 2001.
[3] Dvorkin, Eduardo N., and Klaus‐Jürgen Bathe. “A Continuum Mechanics Based Four‐node Shell Element for General Non‐linear Analysis.” Engineering Computations 1, no. 1 (January 1984): 77–88. https://doi.org/10.1108/eb023562.
[4] Bucalem, M. L., and K. J. Bathe. “Finite Element Analysis of Shell Structures.” Archives of Computational Methods in Engineering 4, no. 1 (March 1997): 3–61. https://doi.org/10.1007/BF02818930.
[5] Shabana, Ahmed A. Dynamics of Multibody Systems. Fourth edition. New York: Cambridge University Press, 2014.
[6] Agrawal, Om P., and Ahmed A. Shabana. “Dynamic Analysis of Multibody Systems Using Component Modes.” Computers & Structures 21, no. 6 (January 1985): 1303–12. https://doi.org/10.1016/0045-7949(85)90184-1.
Extended Capabilities
C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.
Version History
Introduced in R2021b
See Also
MATLAB コマンド
次の MATLAB コマンドに対応するリンクがクリックされました。
コマンドを MATLAB コマンド ウィンドウに入力して実行してください。Web ブラウザーは MATLAB コマンドをサポートしていません。
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)