回答済み
how can i solve this problem?
Hi @worod FOPID, like the ordinary PID, is a static control architecture. The control parameters require the designer to mathem...

2年以上前 | 0

回答済み
Aircraft pitch angle response to elevator inputs
Hi @Daniel Jackson If all the equations are correct, you can use the MATLAB Function block to enter each equation. https://www...

2年以上前 | 0

回答済み
Two figures in to two plots. I need to plot (the density Vs pressure) and ( the density vs. Temperature) for the data itself and using Peng Robinson model.
Hi @Hanadi Previously, didn't @Torsten successfully demonstrate how to plot the Peng–Robinson equation here? Are you expecting ...

2年以上前 | 0

回答済み
Facing difficulty to resolve code problem
Hi @Shakeel Ahmed I recommend using the numerical approach directly when the state equations are available, as in your case. It...

2年以上前 | 0

回答済み
Matlab step() from Simulink dataset
Hi @Oleg Some information is unavailable in your code, but I managed to guess and reproduce the result of the computed LQR gain...

2年以上前 | 0

回答済み
Design and Simulation of optimized Anti-surge Adaptive control system for Centrifugal Compressor
Hi @MADUKA CHIKA To simulate the dynamics and control of the Centrifugal compressor system in MATLAB, you must adhere to a syst...

2年以上前 | 0

回答済み
Simulation and Modelling of a compressor
Hi @MADUKA CHIKA There won't be any detailed technical answer for this general question. However, based on your image, we can a...

2年以上前 | 0

回答済み
My code fails to get value for M (M and K should be very small numbers, close to zero I believe).
Hi @Sean Rotmansky You have one equation, 'g', but you are attempting to solve for two unknown variables, M and K. The system i...

2年以上前 | 0

回答済み
Plotting the derivative of infected population SI model
Hi @Amal Matrafi You can use deval() to obtain the first derivative. Alternatively, as suggested by @Star Strider, you can also...

2年以上前 | 0

回答済み
How to make a phase diagram plot?
Hi @Wing Nam If the analytical solution exists, then you can solve the ODE symbolically using the dsolve() command. From the re...

2年以上前 | 0

回答済み
step response comparison of linear and non linear model
Hi @kruthika u To compare the results, you need to solve the linear system and generate the linear outputs, just as you would f...

2年以上前 | 0

回答済み
how can I keep track of last n sec of data at each time step in Simulink model itself?
Hi @Sowmya Payyavula You can test out this Tapped Delay block. It can store data for the specified number of delay steps.

2年以上前 | 0

| 採用済み

回答済み
Can you share a thesis example about modelling of Unmanned Aircraft Vehicle for Simulink ?
Hi Tahsin, For modeling, reference books are usually very detailed in explaining the derivations of the governing state-space...

2年以上前 | 0

回答済み
I am looking for advice on the best way to learn matlab. I am a second year PhD student trying to familiarize myself with problems or projects. Any advice?
Hi @Mac Kenzie Some prefer to read books, and some learn faster by watching videos. If you are a beginner, I suggest you should...

2年以上前 | 0

回答済み
Error in pole placement
Hi @Ho Pui Sum That is the limitation of the place() command, and it is documentated here. In your case, the rank of the input ...

2年以上前 | 0

回答済み
How to find the Transfer function of a Simulink output plot?
Hi @Atefeh Given the piecewise function defined for I propose a more intuitively understandable Heaviside-based formula, whi...

2年以上前 | 1

回答済み
Help using fsolve (theta beta mach)
Hi @Evan Gehret If you have all the information on the right-hand side of the equation, then I think applying the inverse tange...

2年以上前 | 1

回答済み
Need help to make a ode function asign a value
Hi @Lucas Resende As mentioned by others, we cannot directly test your code because some information about the parameters is no...

2年以上前 | 0

回答済み
I need a help to plots pressure vs. Temp at equilibrium from the attached paper and in the same graph another plot using Peng Robinson model.
I'm not an expert in gas laws, but when the data is available (for example, in the fictional dataset below), you can plot the gr...

2年以上前 | 0

| 採用済み

回答済み
step response of non linear model
Hi @kruthika u Alternatively, you can describe the ODEs and the Outputs in a nonlinear State-Space System: In other words, y...

2年以上前 | 1

| 採用済み

回答済み
step response of non linear model
Hi @kruthika u For general nonlinear ODEs, you can refer to some examples in the ode45 documentation. To plot the state-depende...

2年以上前 | 1

回答済み
Trying to enter a transfer function in simulink (tauD s + 1)
Hi @Wouter Mathematically, is equivalent to in continuous-time domain. As a simple test, if we inject a signal, , which is al...

2年以上前 | 0

回答済み
adding noise to the solution obtained from ode45/dde23
Hi @Muhammad, Does it work if you execute the following? [t, y] = ode45(@odefun, tspan, y0); noise = mynoise(t); % user-...

2年以上前 | 0

| 採用済み

回答済み
Struggling to Solve 2nd Order ODE with Multiple Initial Values
Hi @David Bloom I'm not an expert in self-trapped optical spatial solitons, but I'm attempting to reproduce the graph shown in ...

2年以上前 | 0

回答済み
How can I fix the error message : Each rule must have a consequent pointing to a different output membership function.
Hi @Ahmad As requested, Stage 1 is tuned using PSO, and Stage 2 is tuned using Simulated Annealing. %% Sam's Data for 2 inputs...

2年以上前 | 1

回答済み
How can I fix the error message : Each rule must have a consequent pointing to a different output membership function.
Hi @Ahmad The tunefis() command enables the tuning of fuzzy systems by specifying one of the five optimization methods and thei...

2年以上前 | 1

回答済み
State space system gives incorrect plot
Hi @Julian Thank you for sharing the code. I didn't simulate this in Simulink but in MATLAB using the lsim() command. I plotted...

2年以上前 | 0

| 採用済み

回答済み
Cannot find a suitable controller for my state space system
Hi @Ethan Nobre The performance requirements are not clearly specified, other than addressing unwanted oscillations. Furthermor...

2年以上前 | 0

| 採用済み

回答済み
How to use a global variable when using ode45()?
Hi @David Before delving into the technical aspects of constructing the time-based event-triggered control signal, there are a ...

2年以上前 | 0

回答済み
How can i connect this plot line
Hi @Near Fiern It seems that the endpoint of LxAB is not the same as the starting point of LxCB. You can perform a logical test...

2年以上前 | 0