回答済み
How to include a measured disturbance (ambient temperature and solar radiation) in MPC simulink?model
Hi Maniprasad Sundaramoorthy, To include measured disturbances such as ambient temperature (Ta) and solar radiation (Qsolar) in...

5ヶ月前 | 0

回答済み
Implementing Process Control for Heat Exchanger Networks in MATLAB
Hi Soon Lee, To dynamically model a "Heat Exchanger Network(HEN)", you can use both "MATLAB scripts" and "Simulink". Simulink i...

5ヶ月前 | 0

回答済み
Error search for PV system modelling in Simscape: Problems with the solar module configuration
Hi Israfil-Cihan , The values you have entered for configuring the "Solar cell" seem correct. Here are the few steps you can fo...

5ヶ月前 | 1

| 採用済み

回答済み
Clarification on the Use of beta_Voc_pc Parameter in the official PV Array Module
Hi jinxia zhang, Answer 1: In the official PV array module within MATLAB/Simulink, the “beta_Voc_pc” parameter, which stands...

6ヶ月前 | 1

回答済み
Force measurement using a spherical joint
Hi 석준, When simulating a Stewart platform in “Simscape”, especially when measuring forces at the joints, it's crucial to ensu...

6ヶ月前 | 0

回答済み
Can I load the Rectangular Waveguide with a dielectric fill?
Hi Brian LaRocca, In Antenna Toolbox, the “rectangular waveguide” model does not directly provide a built-in option to specif...

6ヶ月前 | 0

回答済み
sizing of energy management systemwith( EMS) with V2G, how to start do this project how to get the equations by matlab coding
Hi Ahmed, I understand that you are trying to implement V2G functionality using MATLAB. However, Designing and sizing an En...

6ヶ月前 | 0

| 採用済み

回答済み
I am working with c2000 f28379d. In "external mode ", if I set 1 second for LED BLINK, I am getting the same result. But "connected IO mode" fails . How to synchronize.
Hi ARUN, Connected I/O mode and External mode operate differently in terms of how they communicate with the hardware and hand...

6ヶ月前 | 0

回答済み
Creating a Time-Varying RLC Custom Load Component in MATLAB Simulink
Hi Omar Nait Mensour, To connect the custom RLC dynamic load component with other components from Specialized Power Systems lib...

6ヶ月前 | 0

回答済み
I am unable to interface Arduno and simulink with Rhino BLDC motor driver setup to control speed.
Hi Prateek, For open-loop speed control of a BLDC motor using an Arduino Mega 2560 in Simulink, you can follow the below step...

7ヶ月前 | 0

回答済み
Plot trajectory generated by the Driving Scenario Designer
Hi Rajini, To plot the simulation of a vehicle's trajectory over time in a 2D graph using Simulink and the Driving Scenario D...

7ヶ月前 | 0

回答済み
Valid format input to HRPWM module duty cycle control in F28388D
Hi Lior Ben Yehuda, The “HRPWM” block in the C2000 support package with Simulink can typically handle floating-point numbers ...

7ヶ月前 | 0

回答済み
Linux binaries generated by MATLAB OS Manager for SOC blockset create read only /mnt folder unable to pass your own tests of verification and unable to run example models
Hi Sai Kumar, The issue you are facing usually arises when the Linux file system on the board is mounted as read-only and the...

7ヶ月前 | 0

回答済み
Spectrum Analysis on signals in the Simulation Data Inspector
Hi Jack Daniels, It is possible to perform spectrum analysis (Fast Fourier Transform (FFT)) on signals using the Simulation D...

7ヶ月前 | 0

回答済み
Design of Dynamic Voltage Restorer.
Hi Brandon, The design procedure you followed for the “Dynamic Voltage Restorer (DVR)” seems to be quite comprehensive. You ...

7ヶ月前 | 0

回答済み
Simulink Data Inspector offset the time of an entire Run
Hi Stephen McLaren, To Change the time base of a given run by an addition or subtraction to all time entries and update of al...

7ヶ月前 | 1

| 採用済み

回答済み
How can I get 3 outputs from the battery ?
Hi Ahmed ElMashad, To obtain three outputs (State of Charge (SOC), current, and voltage) from the “Battery (Generic model)” b...

7ヶ月前 | 0

回答済み
Simscape - Combine Harmonic Drive Driveline and Multibody
Hi Jannik, To integrate the “Harmonic Drive” block from Simscape Driveline with Simscape Multibody joints and solids, you can...

7ヶ月前 | 0

回答済み
Two-Phase PMLSM mathematical model
Hi Stepan Dvorak, To implement a two phase PMLSM mathematical model from Simscape blocks, you can use: Basic power electroni...

7ヶ月前 | 0

回答済み
How to reduce the effect of one of the manipulated variables in an MPC controller with a MISO model as the internal model?
Hi Dawn Ivan, To increase the effect of one manipulated variable on the output in the MISO model with MPC, you can follow the...

7ヶ月前 | 0

回答済み
How to design an MPC for a nonlinear MISO system?
Hi Nicy Scaria, To build a MISO nonlinear model controlled using MPC in which one input should serve as the manipulated varia...

7ヶ月前 | 0

回答済み
matlab/simulink using digital IO pins ??
Hi Aera, To use the digital IO (e.g. PMOD0_0) pins on the ZCU111 and ZCU216 boards without a pre-existing block in the librar...

7ヶ月前 | 0

| 採用済み

回答済み
Polyspace command line execution
Hi Kalai Ragu, The error message indicates that the script is not receiving a username when trying to connect to the Polyspac...

7ヶ月前 | 0

回答済み
Arduino Mega2560, Support Package for Arduino Hardware Test Connection Failed
Hi Dudu Arife, The serial connection failure with Arduino Mega2560, Support Package for Arduino Hardware can be resolved by t...

7ヶ月前 | 0

回答済み
Nonlinear MPC is not converging. Although the predictions go towards the reference
Hi Marcos, I understand that you are facing a convergence issue due to NPMC Controller as it is not sending new inputs to the...

7ヶ月前 | 0

| 採用済み

回答済み
Interference modeling in simulink
Hi Fumihiko Sato, In interference modelling in Simulink in which the primary signal and the interferer signal are having diff...

7ヶ月前 | 0

回答済み
Is it possible to control Zynq PS MIO using Embedded Coder?
Hi Martin, Simulink primarily interfaces with AXI-connected peripherals on the PL (Programmable Logic) side. You can try the...

7ヶ月前 | 0

回答済み
Virtual Vehicle Composer model doesn't work
Hi Ömer Ergün, The errors you are facing while building EV model using Virtual Vehicle Composer app indicates that: “fatal e...

7ヶ月前 | 0

回答済み
Matlab Battery builder Ambient port to simulate Heat sink with air cooling
Hi Mohammad, You can simulate air cooling without using a coolant plate on the battery module’s bottom using the “Simscape Co...

8ヶ月前 | 1

回答済み
Simscape Battery Capacity Estimator
Hi Gokul, In the result it indicates that the battery capacity drops from 20 Ah to 13.3 Ah over the course of 5 WLTP profiles...

8ヶ月前 | 0