lsm303c

Connect LSM303C sensor on Raspberry Pi hardware I2C bus

expand all in page

Description

The lsm303c object reads ambient temperature, linear acceleration and magnetic field along the X, Y, and Z axes using the STMicroelectronics® I2C-based LSM303C inertial measurement unit (IMU) sensor interfaced with the Raspberry Pi® hardware. Before you use the lsm303c object, ensure that the I2C interface is enabled on your Raspberry Pi kernel. You can then create a connection to the Raspberry Pi board using the raspi object and set its properties. For more information, see raspi.

Note

To generate C/C++ code for this object and its associated functions, you must have an Embedded Coder® license.

Creation

Syntax

sensor = lsm303c(mypi)
sensor = lsm303c(mypi,Name,Value)

Description

sensor = lsm303c(mypi) creates a LSM303C sensor object with default property values. The object represents a connection to the sensor on the Raspberry Pi hardware mypi.

example

sensor = lsm303c(mypi,Name,Value) creates a LSM303C sensor object with properties using one or more Name,Value arguments.

example

Input Arguments

expand all

Raspberry Pi hardware board connection specified as a raspi object.

Example: sensor = lsm303c(mypi) creates a connection to the LSM303C sensor on the Raspberry Pi object mypi.

Name-Value Arguments

expand all

Specify optional pairs of arguments as Name1=Value1,...,NameN=ValueN, where Name is the argument name and Value is the corresponding value. Name-value arguments must appear after other arguments, but the order of the pairs does not matter.

Before R2021a, use commas to separate each name and value, and enclose Name in quotes.

I2C bus address of the Raspberry Pi hardware board.

Example: sensor = lsm303c(mypi, 'Bus', 'i2c-1') creates the sensor object on the 'i2c-1' bus of the Raspberry Pi board.

Data Types: char

Object Functions

readAccelerationRead one acceleration data sample from LSM303C sensor
readTemperatureRead one ambient temperature data sample from LSM303C sensor
readMagneticFieldRead one magnetic field data sample from LSM303C sensor

Examples

collapse all

Ensure that the I2C interface on the Raspberry Pi kernel is enabled and then create an lsm303c sensor object.

You can enable the I2C interface using:

Create a connection from MATLAB® to the Raspberry Pi hardware board.

mypi = raspi('raspberrypi-hysdu8X38o','rocky','bullwinkle')
mypi = 

  Raspi with Properties:

           DeviceAddress: 'raspberrypi-hysdu8X38o'
                    Port: 18734
               BoardName: 'Raspberry Pi 3 Model B+'
           AvailableLEDs: {'led0'}
    AvailableDigitalPins: [4,5,6,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27]
    AvailableSPIChannels: {‘CE0’,’CE1’}
       AvailableI2CBuses: {'i2c-1'}
             I2CBusSpeed: 100000
        AvailabelWebCams: mmal service 16.1 (platform:bcm2835-v4l2)

GPIO header pins I2C_SDA (GPIO 2) and I2C_SCL (GPIO 3) are used for I2C functionality. Display pin mapping of the Raspberry Pi hardware board.

showPins(mypi);
Raspberry Pi 3 Model B+ GPIO Pin Map diagram

Get the addresses of the LSM303C sensor connected to the I2C bus 'i2c-1'.

sensor = scanI2CBus(mypi,'i2c-1');
ans =

  1×2 cell array

    {'0x1D'}    {'0x1E'}

Create an lsm303c sensor object on the I2C bus 'i2c-1' on addresses '0x1D' and '0x1E'.

sensor = lsm303c(mypi,'Bus','i2c-1');
sensor = 

  lsm303c with properties:

                         I2CAddress: 29 ("0x1D")
                                   : 30 ("0x1E")
                                Bus: i2c-1

Extended Capabilities

expand all

Version History

Introduced in R2021a

See Also

| | | | | |

Topics