回答済み
[f28335] I2C transmit status
Hi, Please note when trying to use the I2C Tx and Rx blocks in an implementation for reading multiple bytes of data from slave,...

約5年 前 | 0

回答済み
How to increase acquisition frequency in real time? (TI Board F28379D)
Hi Jessé/Taimur, You can use the 2 model approach when running computation intensive algorithms at high sample rate for data lo...

約5年 前 | 0

回答済み
How to measure control law execution time in Launchxl-F28379D?
Hi Enric, Attached is the model which helps you to achieve the same in simulink w.r.t GPIO bit activation and deactivation. Fe...

約5年 前 | 0

| 採用済み

回答済み
Embedded Coder for C2000
Hi Richard, Attached is the model which i found to be working for DAC-A. The model is created in 2018b version of MATLAB. I fo...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, That can complicate things as the DMA runs in steps of 1, picking next value from table until 500 such iterations ...

約5年 前 | 0

| 採用済み

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, As I mentioned, since the Master ePWM is configured to react on CMPA count and we update the same using DMA ch 1, ...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, I may need your model. Can you attach the up to date model.? Regards, Venkatesh C

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, If you get 200 values in the duty cycle table then you may need to update the DMA configuration w.r.t this. We set...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, To implement deadband, please do the following. Keep all box un-checked for the ePWMxB as shown below as to produ...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, Keeping aside the operation of DMA in this example, we can synchronize the PWM output with help of following confi...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi, Please refer this video: https://in.mathworks.com/matlabcentral/fileexchange/49109-dual-motor-control-with-ti-launchxl-f28...

約5年 前 | 0

回答済み
extra signals DMA example epm Duty Cycle
Hi Gauthier, You may not need other DMA's for generating rest of the PWM's. Once you have the First ePWM working, you can sync...

約5年 前 | 0

回答済み
ADC SCI f28335 problem
Hi Samuel, It may be a good idea to contact us @ https://in.mathworks.com/support/contact_us.html. That can help us better und...

約5年 前 | 0

回答済み
Modify Duty Cycle of ePWM Using DMA
Hi, Please can you run the command at the command prompt: >>which sineTableCalculation.m This will give you the path to the f...

約5年 前 | 0

| 採用済み

回答済み
ADC SCI f28335 problem
Hi Sam, Are you running the model in external mode? Can you try increasing the baudrate of the SCI and see if it helps. Ther...

約5年 前 | 0

回答済み
TI C2000 code generation generates double data type functions instead of single ones
Hi, Please note that the CRL we support are meant to be used for fixed point math. These CRL's don't support float operations. ...

約5年 前 | 2

回答済み
S-function works in normal mode but doesn't in external mode
Hi, Could run the model in external mode and could recieve only zero. I have not debugged the S-Function, but I can recommend ...

約5年 前 | 0

回答済み
S-function works in normal mode but doesn't in external mode
Can you do a crtl+j and send the snap of Sample Time Legend that pop's up as below.

約5年 前 | 0

回答済み
S-function works in normal mode but doesn't in external mode
Hi, When deploying the model on target we configure it for Fixed step disctere solver as the controller runs in discrete amount...

約5年 前 | 0

回答済み
how to execute SCI communication
Hi, Please can you attach the model or snapshots? Do you run one of them in external mode? How are you ensuring the communicati...

約5年 前 | 0

回答済み
ExtTargetPktPending() call failed while checking for target pkt
Hi, A solution depends upon which controller is used, is it controlcard or launchpad? which version of the MATLAB like 2018x? ...

約5年 前 | 0

回答済み
TMS320F28069M: File C:\ProgramData\MATLAB\SupportPackages\R2018b\toolbox\target\supportpackages\tic2000\registry\thirdpartytools\thirdpartytools_win64.xml not found
Hi, Could you please run the 'targetupdater' to configure the supportpackage first. Regards, Venkatesh C

約5年 前 | 0

回答済み
Access multiple I2C sensors with C2000 and simulink
Hi, You may also look in to the implementation of the example model 'c28x_i2c_sensor' here we are sequencing the Tx and Rx oper...

約5年 前 | 0

回答済み
Access multiple I2C sensors with C2000 and simulink
Hi, Please can you refer the example model ' c28x_i2c_eeprom_interrupt'. From this example model one can observe the use of C28...

約5年 前 | 0

回答済み
TMS320F28335: Model for Simulink based buck converter control
Hi, Please let us know if this example works for you. The example would use the ADC and PWM module. https://in.mathworks.co...

約5年 前 | 0

回答済み
C2000 eCAN bus-off condition
Hi, Adding the below line of code should help! HWREG(CANA_BASE + CAN_O_CTL) |= CAN_CTL_ABO; Regards, Venkatesh Chilapu...

約5年 前 | 0

回答済み
C2000 eCAN bus-off condition
Hi, We provide custom code blocks under simulink coder->custom code->System Initialize using which you may initialize the ABO b...

約5年 前 | 1

回答済み
[f28335] I2C transmit status
Hi, Please refer to below link: https://in.mathworks.com/help/supportpkg/texasinstrumentsc2000/ref/c28xi2ctransmit.html The s...

5年以上 前 | 0

回答済み
I want to generate code for TI-Launchpad F28069M by using Simulink. Currently I am using Matlab2016b. Is it possible to genarate code for CCSv8 ? Can you provide me the steps I should follow ?
Please refer the below link for list of compatible CCS and MATLAB version. http://software-dl.ti.com/ccs/esd/documents/ccs_matl...

5年以上 前 | 1

さらに読み込む