回答済み
Breakdown Voltage (BDV) Tester for Transformer Oil
Hello Hatim, you don't actually ask a question or share model details. If you still want help, please ask a specific question ...

3ヶ月前 | 0

回答済み
While Opearting a N channel MOSFET in MATLAB with 100VDC, 100 Ohm load. the MOSFET only allowing 0.2A in each condition but I am expecting of 1A.
Increasing the mosfet threshold voltage will make it conduct less, not more. You need to parameterize the mosfet correctly. In...

4ヶ月前 | 0

回答済み
How can I create a simulation that supplies power to the motor by connecting fuel cells, dc-dc converters, and supercapacitors?
This really depends on how much detail you need for the converter. In general, when doing powertrain analysis, you don't need t...

4ヶ月前 | 0

回答済み
Different Thyristor Gate width gives different waveforms.
Are you sure the results are wrong? You don't have a dc-link capacitor to maintain the dc voltage and with the inductive load a...

4ヶ月前 | 0

回答済み
Better solver for simscape power electronics simulation
You can set your absolute tolerance to be the same as your relative tolerance, and uncheck the option for absolute tolerance. T...

5ヶ月前 | 0

回答済み
Table based battery block choices
You need to have either Simscape Battery or Simscape Electrical installed to have access to the table based battery. Please see...

5ヶ月前 | 0

回答済み
Inconsistent results when simulating an LC series circuit with SimScape
He issue is that the Adams solver is specifially for non-stiff problems and your problem being in simscape is typically a stiff ...

6ヶ月前 | 0

回答済み
Error while running Simulink
This happens when a model has extermely small time constants or challenging equations to solve. That usually means the model is...

6ヶ月前 | 0

回答済み
Thermofluid simulation of an electric motor
This is one starting point: https://www.mathworks.com/help/simscape/ug/motor-thermal-circuit.html and here is another: https://...

6ヶ月前 | 0

回答済み
sic mosfet SPICE models.lib file into Simulink using subcircuit2ssc
Wolfspeed specifically provides LTspice models which use a proprietary interface that is not always compatible with base SPICE. ...

7ヶ月前 | 0

回答済み
Exporting a simulink/Mathlab model as a circuit element for simulation software (Pspice/Cadence)
There are a few options. I am listing them by order of cost (cheapest to most expensive) You can try and utilize the co-simula...

7ヶ月前 | 1

回答済み
PV Mppt constant output voltage
the goal of mppt is to get the optimal power extraction of a solar panel. To accomplish this, the voltage and current must vary...

7ヶ月前 | 1

| 採用済み

回答済み
Sample time relation of controller and PWM switching frequecny
Hello, you are correct that the most common approach is to have the switching frequency be the same as the control frequency. ...

7ヶ月前 | 1

回答済み
How can I export my Simulink electrical circuit into a Matlab function?
The easiest approach to this would be to utilize the sim() command. This lets you set parameters, run a simulation and then get...

7ヶ月前 | 0

回答済み
How can i implement BLDC commutation logic block to a PWM Module?
Please start with this page: https://www.mathworks.com/solutions/electrification/bldc-motor-control.html at the bottom are lin...

7ヶ月前 | 0

| 採用済み

回答済み
Graphs are paused during simulation in Simulink and do not resume once RLC load is added via circuit breaker
It sounds like the simulation is "hanging" aka, it starts taking such small time steps that nothing appears to be happening. Thi...

8ヶ月前 | 0

回答済み
How can I connect my dynamic (mathematical) model of inverter to the grid simulink model?
the most common way to to attatch it to controlled voltage sources for the inverter output and use a controlled current source f...

9ヶ月前 | 0

回答済み
Slip in Asynchronous Block - Induction Machine Squirrel Cage
the block can only give you input for the initial condition of slip, but this does not determine your slip once the model is run...

9ヶ月前 | 0

| 採用済み

回答済み
How the voltage based active cell balancing model works for larger voltage difference and not working for smaller voltage difference ?
You are modelling lithium ion batteries and giving them different nominal voltages. These batteries are not linear and would no...

9ヶ月前 | 0

回答済み
unable to resolve cooling plate error
I think you need to set your number of nodes to 14 and not 14x14 for the cooling plate. If that doesn't solve it, please share ...

9ヶ月前 | 0

| 採用済み

回答済み
How to import .SUBCKT Spice model into MATLAB Simscape?
Unfortunately, there is no guarentee that an imported pspice model will work in simscape. It sounds like you used the command c...

9ヶ月前 | 0

回答済み
How can I gate-off the Average-Value VSC block ?
This will be easier to do with a slightly different block, the Converter (Three Phase). You can set this block to averaged swit...

9ヶ月前 | 0

回答済み
Help me finish the scheme in MATLAB
This issue is that because an ideal transformer is used, it is perfectly isolated from the rest of the circuit. Unfortunately, ...

10ヶ月前 | 1

| 採用済み

回答済み
Rate Transition Data Control
Simulink signals don't support an 'empty' value. They will simply stay at whatever value they were at previously. This is the ...

10ヶ月前 | 0

回答済み
Modeling the Discharge Dynamics of Table-Based Batteries
The battery has the option for turning on dynamics and choosing your resistances and time constants (similar to RC parameters). ...

11ヶ月前 | 0

回答済み
How to operate Front-End Inverter to control variable PMSG output
This is not exactly what you are looking for, but it is a good starting point. This is for a grid connected inverter: https://w...

11ヶ月前 | 0

| 採用済み

回答済み
QZSI SVPWM ZSVM6 method help
I can't tell you exactly what is going on any more than the code can. This shared file is made by an individual user and you ca...

11ヶ月前 | 0

回答済み
Why is my BLDC model not working?
Your overall structure looks good in the picture, please provide more specific questions if you want additional help. I recomme...

11ヶ月前 | 0

回答済み
How to generate SVPWM using HDL code
You have to design your own module if you want it to be hdl compatible. There is no block that does this and generates hdl code...

11ヶ月前 | 0

回答済み
Why is there DC offset present and how can this be removed?
The issue is that the initial conditions are unbalanced and as it's an open circuit with very little current flowing, it'll take...

11ヶ月前 | 0