Manikandan
anna university
Followers: 0 Following: 0
Professional Interests: Electric Drives
統計
ランク
of 144,105
コントリビューション
0 問題
0 解答
スコア
0
バッジ数
0
コントリビューション
0 投稿
コントリビューション
0 パブリック チャネル
平均評価
コントリビューション
0 ハイライト
平均いいねの数
Download any 10 unique submissions
Awarded to Manikandan on 01 Dec 2020
Your submissions were downloaded 10 or more times in a month
Awarded to Manikandan on 01 Nov 2019
Publish your first review
Awarded to Manikandan on 09 Oct 2019
Your submissions received 3 five star ratings
Awarded to Manikandan on 09 Oct 2019
Publish your first submission
Awarded to Manikandan on 09 Oct 2019
Answer 10 questions that were unanswered for more than 30 days
Awarded to Manikandan on 20 Jul 2017
Provide your first answer ever to someone else's question
Awarded to Manikandan on 20 Jul 2017
Feeds
PI control techniques for speed control of a BLDC motor
Try to use trial and error method
約6年 前 | 0
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...
8年弱 前 | 3
送信済み
Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in
約8年 前 | ダウンロード 3 件 |
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...
約8年 前 | 0
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.
約8年 前 | 0
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in
約8年 前 | 0
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...
約8年 前 | 0
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...
約8年 前 | 0
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.
約8年 前 | 0
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in
8年以上 前 | 1
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in
8年以上 前 | 1
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in
8年以上 前 | 0
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]
8年以上 前 | 0
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.
8年以上 前 | 0
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf
8年以上 前 | 0
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.
8年以上 前 | 0
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.
8年以上 前 | 1
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...
8年以上 前 | 0
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.
8年以上 前 | 0
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in
8年以上 前 | 0
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....
8年以上 前 | 0
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...
8年以上 前 | 0
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...
8年以上 前 | 0
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...
8年以上 前 | 0
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in
8年以上 前 | 0
また、以下のリストから Web サイトを選択することもできます。
南北アメリカ
- América Latina (Español)
- Canada (English)
- United States (English)
ヨーロッパ
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)
アジア太平洋地域
- Australia (English)
- India (English)
- New Zealand (English)
- 中国
- 日本Japanese (日本語)
- 한국Korean (한국어)