回答済み
How to save calculated value into Simulink workspace
The easiest thing to do when your system is nonlinear (as in your case) is not to use a State-Space block. Instead, if possible,...

11年弱前 | 1

| 採用済み

回答済み
How to get a transfer function from a Simulink mathematical model synchronous machines?
If you have Simulink Control Design, you can linearize your generator block as shown <http://www.mathworks.com/help/slcontrol/ug...

11年弱前 | 2

回答済み
single-stage single-phase dc-ac converter
SimPowerSystems alreadhas a <http://www.mathworks.com/help/physmod/sps/powersys/ref/pwmgenerator2level.html PWM Generator block>...

11年弱前 | 0

回答済み
Remove input/outputs from stateflow chart
You can open up the Model Explorer and modify all your Stateflow data (input, output, parameters, local, etc.). This is shown in...

11年弱前 | 11

| 採用済み

回答済み
Modeling Pressurized System with SimHydraulics
We'd need to know the parameters of the orifice block and the actual displacement you're feeding it via the Signal Builder block...

11年弱前 | 0

回答済み
How do I connect my wifi robot to matlab via ROS?
You want MATLAB to connect to the IP address of whatever is running the ROS Master. Is that on the rover itself? Once you hav...

11年弱前 | 0

回答済み
StateFlow: Temporal Logic After
If you use transitions and nodes, you don't get the benefits of states "remembering" their previous location. Like you descr...

11年弱前 | 0

回答済み
error in the rosmatlab application: Undefined variable "rosmatlab" or class "rosmatlab.node....
Starting with R2015a, there is an official <http://www.mathworks.com/products/robotics/ Robotics System Toolbox> that replaces a...

11年弱前 | 0

| 採用済み

回答済み
Best way to call Simulink subsystem with various input parameters by skript
If possible, you should convert that subsystem into a separate Simulink model. That lets you call the model by itself using the ...

11年弱前 | 0

回答済み
How to develop the variant subsystem in lower versions of MATLAB?
In older versions, there should be a <http://www.mathworks.com/help/simulink/slref/configurablesubsystem.html Configurable Subsy...

11年弱前 | 0

| 採用済み

回答済み
problem of using rapid accelerator in simulink
LCC is the free compiler which comes with your MATLAB install and is used by default if you have nothing else. The other one you...

11年弱前 | 0

回答済み
What's the difference between MATLAB function block and Interpreted MATLAB function block?
The MATLAB Function block is compiled before run-time (R2014b and earlier, it generates C code and compiles; R2015a and later, i...

11年弱前 | 4

| 採用済み

回答済み
How to set the Diagnostics: Automatic Solver Parameter Selection to none using Matlab work space.
I believe this is the command: set_param(sysName,'SolverPrmCheckMsg','none'); In general, you can right-click the option...

11年弱前 | 1

| 採用済み

回答済み
Calculating eigenmode and eigenfrequency with Simmechanics 2nd generation
If you have access to Simulink Control Design, you could try <http://www.mathworks.com/discovery/linearization.html linearizing...

11年弱前 | 0

回答済み
Set Pressure and Flow Rate in Simulink (SimHydraulics)
I don't believe that is possible, because the Ideal Flow Rate Source will provide whatever pressure is necessary to maintain a g...

11年弱前 | 0

| 採用済み

回答済み
Lego Mindstorms NXT Support Package
Without knowing what the error message is, I know I've run into trouble installing the support package when the install folder i...

11年弱前 | 0

回答済み
Put a Discrete-time ARX model into simulink
The System Identification Toolbox has Simulink blocks in a "System Identification Toolbox" library. For linear ARX models, you c...

11年弱前 | 1

| 採用済み

回答済み
There in no torque actuator in matlab simdriveline.
The <http://www.mathworks.com/help/physmod/simscape/ref/idealtorquesource.html Ideal Torque Source> block is under Simscape > Fo...

11年弱前 | 0

回答済み
Error when trying to setup a feedback control loop in SimMechanics 2nd Gen
As the error message mentions, you need to connect a <http://www.mathworks.com/help/physmod/simscape/ref/solverconfiguration.htm...

11年弱前 | 0

回答済み
HOW TO SET LINEAR/NONLINEAR/UNBALANCED/BALANCED LOAD IN MATLAB SIMULATION???
I'm guessing you have access to SimPowerSystems since you're asking about blocks. The <http://www.mathworks.com/help/physmod/...

11年弱前 | 2

回答済み
How to update the library block
In newer versions of SimPowerSystems, you can connect multiple lines into the same branch. Therefore, you don't need a T-connect...

11年弱前 | 0

| 採用済み

回答済み
Suitable alternative for "T connector element" from old matlab version 6.0 to new matlab2015a version 8.5
It appears that SimPowerSystems was much different in the previous version you refer to, in that the signal lines were Simulink ...

11年弱前 | 0

| 採用済み

回答済み
Selecting the default Intial working directory
There is a MATLAB preference to set the initial working folder: http://www.mathworks.com/help/matlab/matlab_env/preferences.h...

11年弱前 | 0

回答済み
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
If your electrical system is multi-phase -- particularly three-phase -- then the answer is simple: use SimPowerSystems. Other...

11年弱前 | 0

回答済み
How can I "black box" a Simulink Model?
If you have Simulink Coder, you can create a <http://www.mathworks.com/help/simulink/ug/protecting-referenced-models.html protec...

11年弱前 | 1

| 採用済み

回答済み
PID control action for AC reference of variable amplitude and frequency.
You need to do the PID control on a frame that rotates with the AC waveform. In other words, you need to find a way to measure y...

11年弱前 | 0

回答済み
How can I save a Simulink model that uses StateFlow charts which I made using the r2015a release, so that users with r2014a or older may open and run the model?
Are you trying to run the model, save din R2015a format, in an older version? If so, there isn't a guarantee that it will work. ...

11年弱前 | 1

| 採用済み

回答済み
How do I dq0-transform voltage and current in phasor-mode?
What exactly are you trying, and how does it not work? Do you have a screenshot and/or error message? My understanding is tha...

11年弱前 | 0

回答済み
How to use object instances in embedded matlab function
Since "ice" is already a variable visible inside that mask, you could create a parameter in the MATLAB Function block, as shown ...

11年弱前 | 0

回答済み
State space representation using function block in simulink
Any particular reason you are using a MATLAB Function block instead of a <http://www.mathworks.com/help/simulink/slref/statespac...

11年弱前 | 0