回答済み
Shaft dynamic in Simulink with standstill initial condition
Your workaround is a good way to get around it -- however, it makes it such that an initial condition of zero velocity will get ...

10年以上前 | 0

回答済み
Can I emulate a single phase dynamic load starting with a three phase dynamic load
Hi Tony, This is the third place I have seen you ask the same question. Please check the status of your original question, as...

10年以上前 | 0

| 採用済み

回答済み
How to model stress relaxation of spring and dash pot system (parallel or series)?
Force sensors are effectively "zero-resistance" components that should be connected in series, and not in parallel. By connectin...

10年以上前 | 1

| 採用済み

回答済み
Can I access the content of Simdriveline components?
Unfortunately, It's not possible to access the source code for any of the add-on Simscape libraries (SimHydraulics, SimDriveline...

10年以上前 | 1

| 採用済み

回答済み
How to add heat in my model to compensate pressure drop
There are two blocks in the Pneumatic Foundation library that allow you to add heat to the system. These are the <http://www.mat...

10年以上前 | 1

| 採用済み

回答済み
Changeable angle while rotating in SimMechanics Second Generation
Looking at the video, it seems like the yellow and light blue bodies are essentially rigidly connected together at some fixed an...

10年以上前 | 0

回答済み
Error in Stateflow diagram
The error message tells you what's wrong: There are 2 outputs that the chart has to produce, but the chart in its current state ...

10年以上前 | 0

| 採用済み

回答済み
How do I use MathWorks tools to apply Model-Based Design for DO_254?
I would check out the following landing page: http://www.mathworks.com/solutions/aerospace-defense/standards/do-254.html I...

10年以上前 | 1

| 採用済み

回答済み
Derivative of state '1' in block 'X/Y/Integrator' at time 0.55 is not finite.
This usually has to do with really large or infinite signals feeding into an Integrator block. Numerical solvers (expectedly) ha...

10年以上前 | 10

回答済み
Using set_param for multiple variables.
Sure. |sprintf| is handy here. for idx = 1:20 blockName = sprintf('myModel/Constant%i',idx); blockValue = sprint...

10年以上前 | 0

| 採用済み

回答済み
How to get workspace variable data
I think you want to do >> xSeries = get(simout,'x'); >> t = xSeries.Time; >> x = xSeries.Data; - Sebastian

10年以上前 | 0

回答済み
running simulink model from matlab
I don't see a picture attached. If the following doesn't answer your question, please ensure to attach something and I can take ...

10年以上前 | 0

回答済み
Is it possible to model spacecraft in simmechanics. As in spacecraft is not going to be attached to fixed reference frame.What will be the steps for the simulation.
Sure -- this is doable. You will need to place a Joint block between the fixed frame and the spacecraft model. Depending on whet...

10年以上前 | 0

回答済み
How to input the sample time of model (.slx file) from a .m file?
Yes, this is possible using the |set_param| function. Note that the powergui block changed in R2015a (I believe) to be more "Sim...

10年以上前 | 0

| 採用済み

回答済み
Custom Component input: physical signal
I'd suggest enabling <http://www.mathworks.com/help/physmod/simscape/ug/log-navigate-and-plot-simulation-data.html Simscape data...

10年以上前 | 0

| 採用済み

回答済み
Help! How can I implement the variable RLC circuit?
I think you have to take care of this yourself, as shown in this Answer: http://www.mathworks.com/matlabcentral/answers/97917...

10年以上前 | 0

回答済み
Simscape composite component path
The Fixed Orifice Empirical block is actually not directly developed as an |.ssc| file, so you can't use it directly as a compon...

10年以上前 | 0

回答済み
Synchronise ROS with Simulink
What exactly do you mean by this? There's a <http://www.mathworks.com/matlabcentral/fileexchange/29107-real-time-pacer-for-si...

10年以上前 | 0

| 採用済み

回答済み
it is possible to simulate en SPS a variable load in terms of power?
Yes -- there is a <http://www.mathworks.com/help/physmod/sps/powersys/ref/threephasedynamicload.html Three-Phase Dynamic Load bl...

10年以上前 | 0

| 採用済み

回答済み
Why does Simulink generate a sine wave as a triangle wave?
This is definitely a sampling issue. You need to run the model at a faster rate to adequately capture the generated signal. W...

10年以上前 | 3

| 採用済み

回答済み
Torque measurement in Simscape?
If you think of the torque as a "current" that flows in a mechanical "circuit", notice that the torque has two possible paths to...

10年以上前 | 0

回答済み
how can i look at single transformer inrush current waveform when energising the primary from an ac source with no load on the secondary?
Have you seen the |power_transfosat| example model in SimPowerSystems? http://www.mathworks.com/help/releases/R2015b/physmod/...

10年以上前 | 1

| 採用済み

回答済み
How to creat a power system model using Sumulink
That looks fine. As Stefan commented, you can use a Gain block from Simulink > Math Operations if your transfer function is j...

10年以上前 | 0

| 採用済み

回答済み
can Pipe(TL) is used with Pneumatics
You cannot do it directly. The Pipe (TL) block uses the Thermal Liquid domain, which is different from the Pneumatic domain. ...

10年以上前 | 1

| 採用済み

回答済み
linearization problem Linear Parameter Varying (LPV) approximation of Simmechanics model
The |linearize| function can take as a 4th argument a set of <http://www.mathworks.com/help/releases/R2015b/slcontrol/ug/lineari...

10年以上前 | 0

| 採用済み

回答済み
_Matlab Simulink problem about PV Stand alone System_
Notice the X-Y axis coordinates the XY Graph block. The limits are -1 to 1 on both axes. You can double-click the block to open ...

10年以上前 | 0

回答済み
How to configure Belt Drive block for Hardware-in-the-Loop simulation?
The "Friction velocity threshold" parameter is usually the culprit here. This is usually a small region used to avoid numerical ...

10年以上前 | 1

| 採用済み

回答済み
I am using constant block which have value equal to 'abc' and one more block having value equal to 4.I dont want to change the constant block name when the value present is numeric.
Assuming you just want to know if there's a variable or a hard-coded numerical value in your blocks. If so, I would look into th...

10年以上前 | 0

回答済み
Is there a way to pass tables as a parameter to a Simulink "Matlab Function" block?
The MATLAB Function block operates by generating code from the MATLAB code inside it, so the syntax is somewhat restricted. I...

10年以上前 | 0

| 採用済み

回答済み
a way to output a transfer function in the work space to simulink
Do you mean you want to use a transfer function ( |tf| ) variable in a Simulink model? There's an "LTI System" block in the C...

10年以上前 | 0