回答済み
How could I control the thermal coupling between two elements (e.g. two battery cell)?
Dear Mustafa, Thank you for your question. Simscape Electrical has a battery cell block which has the option of turning on the...

約6年 前 | 0

回答済み
How can I speed up my simualtion?
Hello Raphael, Thank you for sharing this. There are several ways in which you could speed up your simulation. They include: R...

約6年 前 | 0

回答済み
Change the capacity of the battery using Generate Parameter Data for Equivalent Circuit Battery Block
Dear Sumukh, The capacity in that block is Battery capacity table. On line 200 of the script Example_DischargePulseEstimation.m...

約6年 前 | 0

回答済み
How do I simulate battery performance in the next 5 years, using existing 5 years trend?
Dear L. Sugu, Thank you for your inquiry. If you have capacity fade and internal resistance increase as part of your last 5 ye...

約6年 前 | 0

回答済み
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hi, Md., You can still use SPS in that case. The main difference with SimElectronics is that the latter models all nonlineari...

10年以上 前 | 0

回答済み
¿Why the battery (electrical source component in SimPowerSystem Matlab/Simulink toolbox) discharge at the same rate with different capacities?
Hello, Jorge, I am attaching a model like you describe above and it seems to work correctly for me. Please make sure you cli...

10年以上 前 | 0

| 採用済み

回答済み
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hello, Md., If the AC part of your system is three-phase and you can neglect thermal effects on the semiconductor devices and...

10年以上 前 | 0

回答済み
How can I generate the setup of AC sweep for AC Voltage source in either Matlab or simulink?
Hello, Robert, I believe the Chirp Signal may do the job for you. It is in the Sources section of the Simulink library. Be...

11年弱 前 | 0

| 採用済み

回答済み
Problems with model behaviour, hanging-up in a loop.
Hello, Joel, Would you please attach the model to this thread so I can take a look and try to better understand the issue? ...

11年弱 前 | 0

| 採用済み

回答済み
How to model a solar powered electric grid in Simulink?
Hello, Faraz, I suggest you consider the use of SimPowerSystems for your design. You can find some examples here: http://w...

11年弱 前 | 1

| 採用済み

回答済み
Simscape thermal mass discrete model
Dear Lalumet, A discrete solver can be used if you set up "Use Local Solver" in the Simscape Solver configuration block. Ple...

11年弱 前 | 0

回答済み
How to make a Variable resistor in Sim powersystem not Simscape.
Hello, Adroit, You can combine a current meter and a controlled voltage source to create a variable resistor. Please see att...

約11年 前 | 2

| 採用済み

回答済み
Battery Model Simulink for 12V
Hi, Samad, Please open the battery cell block and comment out the SOC, DOC, and T blocks. This will prevent the second error ...

約11年 前 | 1

| 採用済み

回答済み
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Yes, that is possible. There are a couple of options: 1) Use SimPowerSystems Simscape Components. The blocks...

約11年 前 | 0

| 採用済み

回答済み
lead acid battery simulink
Hello, Simon, You may want to check this submission for an example of what you are trying to model: http://www.mathworks.c...

約11年 前 | 0

回答済み
Battery Model Simulink for 12V
Hi, Samad, The series connection in Simscape is realized connecting the + terminal of each cell to the - terminal if the adja...

約11年 前 | 0

回答済み
Bringing battery simulation results (parameter estimation) to hardware
Hello, Valentin, Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond des...

約11年 前 | 0

| 採用済み

回答済み
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Can you please attach a screenshot of your model so that I can take a look? Your problem is typically related ...

約11年 前 | 0

回答済み
Error with Simscape simulating
Hello, Nikolaos, Your model is missing an electrical reference (ground). Please add one and let me know if you still get an e...

約11年 前 | 5

回答済み
Recharge battery by induction on simulink
Hello, Titouan, Please try inserting an electrical reference block on the right hand side of your magnetic circuit. It needs ...

約11年 前 | 0

| 採用済み