Hydraulic valve that allows flow in one direction only
The Shuttle Valve block represents a hydraulic shuttle valve as a data-sheet-based model. The valve has two inlet ports (A and A1) and one outlet port (B). The valve is controlled by pressure differential . The valve permits flow either between ports A and B or between ports A1 and B, depending on the pressure differential pc. Initially, path A-B is assumed to be opened. To open path A1-B (and close A-B at the same time), pressure differential must be less than the valve cracking pressure (pcr <=0).
When cracking pressure is reached, the valve control member (spool, ball, poppet, etc.) is forced off its seat and moves to the opposite seat, thus opening one passage and closing the other. If the flow rate is high enough and pressure continues to change, the control member continues to move until it reaches its extreme position. At this moment, one of the valve passage areas is at its maximum. The valve maximum area and the cracking and maximum pressures are generally provided in the catalogs and are the three key parameters of the block.
The relationship between the A-B, A1–B path openings and control pressure pc is shown in the following illustration.
In addition to the maximum area, the leakage area is also required to characterize the valve. The main purpose of the parameter is not to account for possible leakage, even though this is also important, but to maintain numerical integrity of the circuit by preventing a portion of the system from getting isolated after the valve is completely closed. An isolated or "hanging" part of the system could affect computational efficiency and even cause failure of computation. Therefore, the parameter value must be greater than zero.
The model accounts for the laminar and turbulent flow regimes by monitoring the Reynolds number for each orifice (ReAB,ReA1B) and comparing its value with the critical Reynolds number (Recr). The flow rate through each of the orifices is determined according to the following equations:
|qAB, qA1B||Flow rates through the AB and A1B orifices|
|pAB, pA1B||Pressure differentials across the AB and A1B orifices|
|pA, pA1, pB||Gauge pressures at the block terminals|
|CD||Flow discharge coefficient|
|AAB, AA1B||Instantaneous orifice AB and A1B passage areas|
|Amax||Fully open orifice passage area|
|Aleak||Closed valve leakage area|
|pc||Valve control pressure differential|
|pcrack||Valve cracking pressure differential|
|pop||Pressure differential needed to fully shift the valve|
|pcrAB, pcrA1B||Minimum pressures for turbulent flow across the AB and A1B orifices|
|Recr||Critical Reynolds number|
|DHAB, DHA1B||Instantaneous orifice hydraulic diameters|
|ν||Fluid kinematic viscosity|
By default, the block does not include valve opening dynamics. Adding valve opening dynamics provides continuous behavior that is particularly helpful in situations with rapid valve opening and closing. The orifice passage areas AAB and AA1B in the equations above then become steady-state orifice AB and A1B passage areas, respectively. Instantaneous orifice AB and A1B passage areas with opening dynamics are determined as follows:
|AAB_dyn||Instantaneous orifice AB passage area with opening dynamics|
|AA1B_dyn||Instantaneous orifice A1B passage area with opening dynamics|
|AAB_init||Initial open area for orifice AB|
|τ||Time constant for the first order response of the valve opening|
The block positive direction is from port A to port B and from port A1 to port B. Control pressure is determined as .
Valve opening is linearly proportional to the pressure differential.
No loading on the valve, such as inertia, friction, spring, and so on, is considered.
Valve passage maximum cross-sectional area. The default value
Pressure differential level at which the orifice of the valve
starts to open. The default value is
Pressure differential across the valve needed to shift the valve
from one extreme position to another. The default value is
Semi-empirical parameter for valve capacity characterization.
Its value depends on the geometrical properties of the orifice, and
usually is provided in textbooks or manufacturer data sheets. The
default value is
The maximum Reynolds number for laminar flow. The transition
from laminar to turbulent regime is assumed to take place when the
Reynolds number reaches this value. The value of the parameter depends
on the orifice geometrical profile. You can find recommendations on
the parameter value in hydraulics textbooks. The default value is
The total area of possible leaks in the completely closed valve.
The main purpose of the parameter is to maintain numerical integrity
of the circuit by preventing a portion of the system from getting
isolated after the valve is completely closed. The parameter value
must be greater than 0. The default value is
Select one of the following options:
Do not include valve opening dynamics —
The valve sets its orifice passage area directly as a function of
pressure. If the area changes instantaneously, so does the flow equation.
This is the default.
Include valve opening dynamics —
Provide continuous behavior that is more physically realistic, by
adding a first-order lag during valve opening and closing. Use this
option in hydraulic simulations with the local solver for real-time
simulation. This option is also helpful if you are interested in valve
opening dynamics in variable step simulations.
The time constant for the first order response of the valve
opening. This parameter is available only if Opening dynamics is
Include valve opening dynamics.
The default value is
The initial open area for orifice AB. This parameter is available
only if Opening dynamics is set to
valve opening dynamics. The default value is
Parameters determined by the type of working fluid:
Fluid kinematic viscosity
The block has the following ports:
Hydraulic conserving port associated with the valve inlet.
Hydraulic conserving port associated with the valve inlet.
Hydraulic conserving port associated with the valve outlet.