Technical Articles

  • Next-Generation Endoscopic Surgical Stapler Prototyping

    Learn more
  • Developing Motion Analysis Algorithms

    Learn more
  • Student Team Wins Freescale Cup with Model-Based Design

    Learn more

Filter all Articles

Results

   
Article Published
A rapid prototyping workflow based on Model-Based Design enables Ethicon Endo-Surgery engineers to implement and test new design refinements in minutes and reduce overall development time by months.
2015年1月
By developing and testing motion analysis algorithms in MATLAB® and generating C code with MATLAB Coder™ dorsaVi engineers cut development time by almost half compared to their previous approach, which involved hand-coding in C#.
2014年12月
Model-Based Design enabled students with no previous design experience to model their car, tune key performance parameters, evaluate control ideas, and develop an electronic differential to keep the car on the track during high-speed turns.
2014年11月
This article describes best practices for creating, implementing, validating, and promoting new modeling guidelines.
2014年9月
Article describes method for controlling AFR that combines low cost of conventional switching oxygen sensor and streamlined catalyst conversion efficiency calibration made possible by direct adjustment of exhaust AFR amplitude, frequency, and bias.
2014年9月
Engineers use MATLAB and Simulink to analyze image and signal data, design controls and signal processing algorithms, implement their designs in software after thorough verification and validation, and generate reports for standards compliance.
2014年8月
Support packages for low-cost hardware platforms from Arduino to Zynq let you stream sensor data into MATLAB and generate code to run Simulink models on real hardware.
2014年8月
As their fourth-year undergraduate capstone project, Penn students used MATLAB and Simulink to design and build Titan Arm, a controllable, wireless exoskeleton capable of lifting more than 40 pounds.
2014年1月
This paper outlines the requirements and considerations for developing and deploying physical system models.
2014年1月
This paper presents best practices for completing projects certified to DO-178B and DO-178C using Model-Based Design. Included are key considerations, methods, and capabilities of Model-Based Design spanning the software development process.
2013年12月
A MATLAB and Simulink workflow for developing a desktop or lab dynamometer capable of running at lower DC bus voltages.
2013年12月
Using industry-standard tools such as MATLAB and Simulink, and low-cost hardware such as Arduino, Beagleboard, LEGO MINDSTORMS, and Raspberry Pi, students tackle real engineering problems and acquire the skills they will need for careers in industry.
2013年10月
Third-party products help developers prototype and deploy human machine interface (HMI) applications with integrated graphics and multi-touch and voice input using Model-Based Design.
2013年10月
Engineers and scientists connect MATLAB and Simulink to FPGAs, microprocessors, cameras, instruments, and other hardware to design, test, and verify systems that combine hardware and software components.
2013年10月
This article presents three practical approaches to early verification using Model-Based Design: automated verification and test bench reuse, multidomain modeling, and rapid prototyping.
2013年10月
This paper shows how engineers can determine whether their design is sufficiently covered by a set of requirements-based test vectors.
2013年9月
UPenn has developed a first-of-its-kind electrophysiological model of the heart that enables real-time closed-loop testing and early verification of pacemakers by simulating a variety of heart conditions.
2013年6月
With a custom rapid control prototyping platform and Model-Based Design, Hella engineers produce a real-time prototype incorporating 80% of the final product’s functionality in a few months.
2013年3月
This paper compares Model-Based Design approaches for developing logic-intensive algorithms in a high-integrity environment.
2013年2月
This paper examines common Stateflow design constructs. It explores the performance of architectural decisions such as state actions versus transition actions, events versus transition conditions, and MATLAB® versus C as the action language.
2013年2月
Identify a plant model from input-output data, use the identified model to design a controller, and implement the controller on an embedded microprocessor.
2013年1月
This is a supplement to the article, "Motor Control with Arduino: A Case Study in Data-Driven Modeling and Control Design."
2013年1月
An interview with a senior Simulink development team lead and an example showing how Simulink R2012b simplifies model navigation, simulation analysis, and model editing.
2013年1月
Model-Based Software Design, an elective course for fifth-year students, prepares future engineers by combining lectures and practical exercises with seminars conducted by local industry experts.
2012年12月
To improve code quality, development teams complement traditional software verification activities with static code analysis using Polyspace code verifiers, which use formal methods with abstract interpretation to verify C, C++, or Ada code.
2012年12月
This paper discusses a verification and validation workflow for developing in-vehicle software components which need to comply with ISO 26262-6 using Model-Based Design.
2012年12月
2012年11月
Guidance on complying with the new standards within Model-Based Design.
2012年7月
Techniques based on formal methods for verifying complex avionics systems.
2012年7月
Analyzing source code for quality and reliability with Polyspace code verifiers.
2012年6月
Automating the transition from Simulink models representing analog and digital components to HDL descriptions using HDL Coder.
2012年5月
This paper describes the interoperability of tools that support Model-Based Design. It focuses on mechanisms defined by AUTOSAR, and outlines how to verify and validate designs at different stages in the workflow.
2012年5月
Septentrio streamlines the DO-178B certification process with MATLAB and Simulink.
2012年5月
This paper describes how it is impossible to use traditional testing methods in order to test complex software systems. It shows how engineers can use formal methods to specify the full range of data in the calibration tables and verify software.
2012年4月
TNO's shockwave-damping software helps ensure smooth traffic flow after sudden braking incidents.
2012年4月
Measure code efficiency and perform rigorous code verification using MATLAB, Simulink, and Embedded Coder.
2012年3月
A challenging controls project gives many students the skills of seasoned engineers well before they graduate.
2012年2月
This paper presents an integrated approach for the development of complex aerospace systems. To better illustrate the scope of this technique, a case study for a complex aerospace model based on the HL-20 personnel launch system is provided.
2012年1月
This article discusses the recommended three-step workflow for converting MATLAB algorithms automatically into C code. Generating C code from MATLAB results in less time spent programming in a lower level language and in faster design iterations.
2011年8月
Polyspace identified the 97% of code that was free of certain run-time errors, enabling Elektrobit to focus code reviews on the remaining 3%.
2011年6月
This paper describes the tool classification and qualification approach of ISO/FDIS 26262 “Road Vehicles - Functional Safety” and summarizes the authors’ firsthand experiences with implementing this approach for development and verification tools.
2011年4月
This paper presents a set of practical strategies for determining the first steps to take when using Model-Based Design and code generation in production development processes.
2010年12月
This paper recommends best practices for creating an infrastructure and deploying large-scale models for embedded applications using Model-Based Design.
2010年12月
This article describes techniques for generating code from Simulink models and integrating that code into corporate simulation environments. The techniques are based on actual aerospace use cases.
2010年1月
In this paper, the minimum number of test measurements required to optimally calibrate the steady-state spark advance and cam-phaser settings of a SI DIVCP engine is determined using a high-fidelity model of a 2.2L SI DIVCP engine.
2009年12月
This paper reviews case studies of large-scale deployment of Model-Based Design and standards enforcement automation.
2009年1月
This paper illustrates how Model-Based Design integrates the world of system designers, FPGA designers, and verification engineers to increase productivity and produce correct-by-construction designs that match the system specification.
2009年1月
This paper introduces techniques that can be used to generate and measure code constructs for creating a set of best practices for the Simulink® modeling environment.
2009年1月
This paper discusses a verification and validation workflow using Model-Based Design for developing in-vehicle software components to meet IEC 61508 standards.
2009年1月
This paper uses an acoustic tone controls application example to describe a workflow using Model-Based Design to develop an algorithm with selectable banks of fixed-point digital filters.
2009年1月
This paper examines methods used for creating custom blocks and nongraphically represented code to create a Simulink interface to common utility services such as communications, diagnostics, and nonvolatile memory.
2009年1月
This paper addresses two important workflow issues to support the design and verification of HMI logic: integration of the HMI graphics and logic, and formal verification of the logic using a virtual HMI connected to a Simulink® model.
2008年12月
This paper shows how Model-Based Design can be used to address challenges facing engineers developing commercial vehicle electronics systems.
2008年12月
This paper describes recent advances in verification, validation, and test technologies involving Model-Based Design with production code generation.
2008年12月
Article presents a methodology for applying Model-Based Design to develop and automatically optimize vehicle stability control systems.
2008年11月
Using a fault-tolerant fuel system model as an example, this article describes tools and a workflow for converting models from floating- to fixed-point for production code generation. The approach described uses two tools in Simulink Fixed Point.
2008年11月
PolySpace products use sophisticated math and analysis to prove the absence of run-time errors without the need to compile and run the code.
2008年9月
An integrated framework enables technicians unfamiliar with communications theory to specify an SDR design at a high level of abstraction.
2008年9月
Aerospace, automotive, communications, mechatronics and other organizations solve the challenge of verifying and validating embedded systems comprising software and electronics.
2008年9月
Using a radio face plate as an example, this paper shows how to create a “soft” representation of an HMI, record the test procedure, export it to an editable file, and use the file to populate a test harness within Simulink®.
2007年12月
This paper describes how John Deere adopted Model-Based Design for commercial vehicle development and discusses the benefits and lessons learned.
2007年12月
Engineers used Model-Based Design and rapid prototyping to build and test a controller before the fuel cell plant was available.
2007年6月
This paper discusses the challenges of performing configuration management of the models and associated files central to Model-Based Design for use in a production environment.
2007年4月
This article describes a process for creating a parameterized battery model capable of providing accurate simulation results and fast simulation speed.
2007年4月

Receive the latest MATLAB and Simulink technical articles.

Related Resources

Latest Blogs